84870A
1.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for LHD without Power Retract Mirror)
Check the mirror select and surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select and surface adjust switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=6,2,7,11,4 |
||
| L14-6 (B) - L14-2 (VL) | Up | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Up | Below 1 Ω |
| L14-6 (B) - L14-2 (VL) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Down | Below 1 Ω |
| L14-7 (E) - L14-2 (VL) | Down | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-2 (VL) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-4 (HL) | Left | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Left | Below 1 Ω |
| L14-6 (B) - L14-4 (HL) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Right | Below 1 Ω |
| L14-7 (E) - L14-4 (HL) | Right | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-4 (HL) | Off | 10 kΩ or higher |
Turn the mirror select and surface adjust switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=6,5,7,11,3 |
||
| L14-6 (B) - L14-5 (VR) | Up | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Up | Below 1 Ω |
| L14-6 (B) - L14-5 (VR) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Down | Below 1 Ω |
| L14-7 (E) - L14-5 (VR) | Down | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-5 (VR) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-3 (HR) | Left | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Left | Below 1 Ω |
| L14-6 (B) - L14-3 (HR) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Right | Below 1 Ω |
| L14-7 (E) - L14-3 (HR) | Right | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-3 (HR) | Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=12,1 |
|
| L14-12 (ILL+) - Auxiliary battery positive (+)
L14-1 (ILL-) - Auxiliary battery negative (-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A
2.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for LHD with Power Retract Mirror)
Check the mirror select and surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select and surface adjust switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=6,2,7,11,4 |
||
| L14-6 (B) - L14-2 (VL) | Up | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Up | Below 1 Ω |
| L14-6 (B) - L14-2 (VL) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Down | Below 1 Ω |
| L14-7 (E) - L14-2 (VL) | Down | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-2 (VL) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-4 (HL) | Left | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Left | Below 1 Ω |
| L14-6 (B) - L14-4 (HL) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Right | Below 1 Ω |
| L14-7 (E) - L14-4 (HL) | Right | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-4 (HL) | Off | 10 kΩ or higher |
Turn the mirror select and surface adjust switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=6,5,7,11,3 |
||
| L14-6 (B) - L14-5 (VR) | Up | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Up | Below 1 Ω |
| L14-6 (B) - L14-5 (VR) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Down | Below 1 Ω |
| L14-7 (E) - L14-5 (VR) | Down | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-5 (VR) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-3 (HR) | Left | Below 1 Ω |
| L14-7 (E) - L14-11 (M+) | Left | Below 1 Ω |
| L14-6 (B) - L14-3 (HR) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-6 (B) - L14-11 (M+) | Right | Below 1 Ω |
| L14-7 (E) - L14-3 (HR) | Right | Below 1 Ω |
| L14-6 (B) - L14-11 (M+) | Off | 10 kΩ or higher |
| L14-7 (E) - L14-3 (HR) | Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror retract switch.
| *a | Retractable Outer Mirror Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=9,8,10 |
||
| L14-9 (MAT) - L14-8 (E) | AUTO position | Below 1 Ω |
| L14-9 (MAT) - L14-8 (E) | Except AUTO position | 10 kΩ or higher |
| L14-10 (MR) - L14-8 (E) | Retract position | Below 1 Ω |
| L14-10 (MR) - L14-8 (E) | Except retract position | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
Click Location & Routing(L14)Location & Routingewd_type=routing;type=c;code=L14 Click Connector(L14)Body>Front Door Wire LH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=L14;pinno=12,1 |
|
| L14-12 (ILL+) - Auxiliary battery positive (+)
L14-1 (ILL-) - Auxiliary battery negative (-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A
3.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for RHD without Power Retract Mirror)
Check the mirror select and surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select and surface adjust switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=6,2,7,11,4 |
||
| K12-6 (B) - K12-2 (VL) | Up | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Up | Below 1 Ω |
| K12-6 (B) - K12-2 (VL) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Down | Below 1 Ω |
| K12-7 (E) - K12-2 (VL) | Down | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-2 (VL) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-4 (HL) | Left | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Left | Below 1 Ω |
| K12-6 (B) - K12-4 (HL) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Right | Below 1 Ω |
| K12-7 (E) - K12-4 (HL) | Right | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-4 (HL) | Off | 10 kΩ or higher |
Turn the mirror select and surface adjust switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=6,5,7,11,3 |
||
| K12-6 (B) - K12-5 (VR) | Up | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Up | Below 1 Ω |
| K12-6 (B) - K12-5 (VR) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Down | Below 1 Ω |
| K12-7 (E) - K12-5 (VR) | Down | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-5 (VR) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-3 (HR) | Left | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Left | Below 1 Ω |
| K12-6 (B) - K12-3 (HR) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Right | Below 1 Ω |
| K12-7 (E) - K12-3 (HR) | Right | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-3 (HR) | Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=12,1 |
|
| K12-12 (ILL+) - Auxiliary battery positive (+)
K12-1 (ILL-) - Auxiliary battery negative (-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.
84870A
4.INSTALL OUTER MIRROR SWITCH ASSEMBLY (for RHD with Power Retract Mirror)
Check the mirror select and surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select and surface adjust switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=6,2,7,11,4 |
||
| K12-6 (B) - K12-2 (VL) | Up | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Up | Below 1 Ω |
| K12-6 (B) - K12-2 (VL) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Down | Below 1 Ω |
| K12-7 (E) - K12-2 (VL) | Down | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-2 (VL) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-4 (HL) | Left | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Left | Below 1 Ω |
| K12-6 (B) - K12-4 (HL) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Right | Below 1 Ω |
| K12-7 (E) - K12-4 (HL) | Right | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-4 (HL) | Off | 10 kΩ or higher |
Turn the mirror select and surface adjust switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=6,5,7,11,3 |
||
| K12-6 (B) - K12-5 (VR) | Up | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Up | Below 1 Ω |
| K12-6 (B) - K12-5 (VR) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Down | Below 1 Ω |
| K12-7 (E) - K12-5 (VR) | Down | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-5 (VR) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-3 (HR) | Left | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Left | Below 1 Ω |
| K12-6 (B) - K12-3 (HR) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Right | Below 1 Ω |
| K12-7 (E) - K12-3 (HR) | Right | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-3 (HR) | Off | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check the mirror retract switch.
| *a | Retractable Outer Mirror Switch |
| *b | Component without harness connected
(Outer Mirror Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=9,8,10 |
||
| K12-9 (MAT) - K12-8 (E) | AUTO position | Below 1 Ω |
| K12-9 (MAT) - K12-8 (E) | Except AUTO position | 10 kΩ or higher |
| K12-10 (MR) - K12-8 (E) | Retract position | Below 1 Ω |
| K12-10 (MR) - K12-8 (E) | Except retract position | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=12,1 |
|
| K12-12 (ILL+) - Auxiliary battery positive (+)
K12-1 (ILL-) - Auxiliary battery negative (-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.