Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2021.07
RM3700E _51 Engine / Hybrid System _105429 STOP AND START _0482038 STOP AND START SYSTEM D

STOP AND START  STOP AND START SYSTEM  SYSTEM DESCRIPTION  


STOP AND START CONTROL


The stop and start system operates according to the following conditions, achieving appropriate engine stop and start control together with safe and smooth driving characteristics.

a.

When all of the conditions in the following table have been met, the engine is stopped by stop and start control.

Item Condition
(All of the following conditions are met)
Idle Stop Push Start Switch Assembly*1 More than 5 seconds elapsed at ON
Ignition or Starter Switch Assembly*2
Engine Coolant Temperature 40 to 105°C (104 to 221°F)
Ambient Temperature More than -5°C (23°F)
Driver Door 3 seconds have elapsed after driver door closed
Driver Seat Belt Driver side buckle is latched
Steering Speed Less than 45 deg/s
Brake Booster Vacuum On a flat place, more than 1 second elapses at more than 42.5 kPa (Threshold values change according to road surface gradient and brake master pressure.)
Shift Position Shift lever is in neutral
Stop and Start System Cancel Switch (Combination Switch Assembly) OFF
Vehicle Speed 0 km/h (0 mph) (After the engine has warmed up and is running)
Engine Speed 1250 rpm or less (changes according to engine coolant temperature)
Hood 3 seconds have elapsed after engine hood closed (However, permitted when engine started after more than 30 seconds elapsed with ignition switch off state and [ON: engine hood close]
Auxiliary Battery Voltage
When using specified battery:

8.2 V or higher when starter begins operation and 8.2 V or higher when cranking


When using non-specified battery:

8.92 V or higher when starter begins operation and 8.92 V or higher when cranking


Auxiliary Battery Fluid Temperature*4 -10°C or higher and 70°C or less (14°F or higher and 158°F or less)
Idle Stop Auxiliary Battery Integrated Current*5
One of the following conditions is met:
·

-3974 A-sec or more: "Status of Battery Charge Control"*6 is Charge Control Coordination Mode, Stop and Start Standalone Mode or Low Temperature Mode

·

0 A-sec or more: "Status of Battery Charge Control"*6 is Stop and Start Restriction Mode or Temperature High/Low Mode


Auxiliary Battery Charge Control The value of Data List item Status of Auxiliary Battery Charge Control is not Refresh Charge Mode, Abnormal Mode or Battery Condition Judgment Mode.
Idling Stop Rate /
Total Idling Stop Rate
·

Idling stop rate for one trip: 50% or less.

·

Total idling stop rate: 40% or less.


HINT:
·

Idling stop rate: Idling stop rate for ignition on time (1 trip)

·

Total idling stop rate: Idling stop rate for total ignition on time



Air Conditioning
Any of the following conditions are met:
·

Defogger Switch: OFF, and Blower Switch: OFF

·

With blower switch on, evaporator temperature below threshold (varies depending on each temperature, humidity, amount of solar radiation, etc.) and after certain period of time since engine restarted by stop and start system (threshold varies depending on idling stop conditions)


Heater
One of the following conditions is met:
·

Blower switch is off

·

While blower switch is on and A/C switch is off, one of the following conditions is met:

-

Ambient temperature is higher than 10°C, or

-

Engine coolant temperature is higher than 55°C, or

-

Vehicle cabin temperature is higher than the set temperature - 5°C


·

While blower switch is on and A/C switch is off, a certain amount of time has elapsed after engine state changed from "not running" to "running".


Cooler
One of the following conditions is met:
·

Blower switch is off

·

A/C switch is off

·

Ambient temperature 23°C (73°F) or less

·

Evaporator internal temperature less than 9°C (48°F), air mix damper opening value more than 10%, and vehicle cabin temperature less than 3°C (37°F) above set temperature or blower level less than 16 (when ignition switch turned to ON for first time in one trip)


Engine Control
·

Engine catalytic warm up is completed

·

Engine control learning has completed

Click here(Click here)



*1: w/ Entry and Start System

*2: w/o Entry and Start System


HINT:
·

*3: Enough brake force is applied to prevent the vehicle from moving when the engine is started again.

·

*4: When the auxiliary battery fluid temperature is -15°C (5°F) or less, or 75°C (167°F) or higher, stop and start control is prohibited. When the auxiliary battery fluid temperature returns to -10°C (14°F) or higher, and 70°C (158°F) or less, stop and start control is permitted.

·

*5: Read the Data List items "Integrated Current" and "Stop&Start Operating Permission (Integrated Current)" when checking the integrated current value.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST

·

*6: Please refer to the Data List "Status of Auxiliary Battery Charge Control" for information about the status of the auxiliary battery charge control.




b.

When the engine is stopped by stop and start control, and any of the following conditions are met, the engine will restart.

Item Condition
(Any of the following conditions is met)
Engine Restart Brake Booster Vacuum Brake booster vacuum insufficient (Under 37.5 kPa (0.38 kg/cm2, 5.4 psi)) (Brake booster vacuum changes in accordance with brake fluid pressure (brake pedal effort))
SFI System Malfunction in SFI system is detected
Power Steering System Malfunction in power steering system is detected
Air Conditioning Timer in the air conditioning amplifier assembly runs out
Heater Timer in the air conditioning amplifier assembly runs out
Air Conditioning/Heater
Both of the following conditions are met:
·

Blower switch: ON

·

Evaporator temperature exceeds threshold value (threshold value varies with temperature, humidity and amount of solar radiation)


Any of the following conditions are met: from OFF to ON
·

A/C switch, blower switch: from OFF to ON

·

Defogger switch: from OFF to ON

·

During blower OFF and Auto control, when it changed to manual blower

·

Changes from stop and start system priority control to normal system control


Auxiliary Battery Auxiliary battery voltage drops (11.4 V or less)
Auxiliary Battery Integrated Current*1 The accumulated value of discharge current during engine stop is too large (5184 A-sec or more)
Vehicle Speed Vehicle speed signal is input (Vehicle stopped on a slope, etc.)
Driver Door Open
Driver Seat Belt Driver seat belt is unfastened
Steering Wheel Steering wheel turned 25 degrees or more
Stop and Start System Cancel Switch (Combination Switch Assembly) When stop and start system cancel switch (combination switch assembly) is turned from off to on
Clutch pedal Clutch pedal is depressed

HINT:

*1: Read the Data List items "Integrated Current" and "Stop&Start Operating Permission (Integrated Current)" when checking the integrated current value

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DATA LIST / ACTIVE TEST





WARNING CONTROL


If any of the following operations are performed while the engine is stopped due to stop and start control, the system will not restart the engine. The engine will change the mode from "stopped due to system control" to "stalled" or the driver will be warned using the buzzer.

Operation Warning Control
The engine hood is opened with the shift lever in neutral The engine stops (mode changes to "stalled", and the engine cannot be restarted until the ignition switch is turned off and then to ON)
The shift lever is operated without depressing the clutch pedal The buzzer sounds and stop and start indicator blinks (engine will not start)
The driver seat belt is unfastened The engine starts


WARNING INDICATOR AND BUZZER OPERATION


A287227C01
0.677,0.271 1.031,0.583 0.354,0.313 10 *a 0.677,1.729 1.031,2.042 0.354,0.313 10 *b
*a Stop and Start Indicator
*b Stop and Start Cancel Indicator


The driver is informed of the system control status and warnings by the stop and start indicator, stop and start cancel indicator and the buzzer.

HINT:

The stop and start indicator and the stop and start cancel indicator are displayed at the same location in the combination meter.

One or the other will be displayed according to the order of priority, but they will not be illuminated simultaneously.


Stop and Start Indicator and Buzzer Operation
Item Condition Stop and Start Indicator
(Green)
Stop and Start Cancel Indicator
(Orange)
Buzzer
For 3 seconds after the ignition switch to ON Normal operation Comes on Comes on Does not sound
During stop and start control operation (engine is stopped) Normal operation Comes on Does not come on Does not sound
The shift lever is operated without depressing the clutch pedal Blinks at 0.15 second interval Does not come on Sounds
Control is prohibited by the stop and start system cancel switch (combination switch assembly) Normal operation Does not come on Comes on Does not sound
Diagnostic trouble code Any DTCs are stored Does not come on Blinks at 0.5 second interval Does not sound
Starter assembly life Number of times the starter has been operated exceeds its limit Does not come on Blinks at 0.5 second interval Does not sound


MULTI-INFORMATION DISPLAY MESSAGE AND INDICATOR OPERATION


An indicator and/or messages are displayed on the multi-information display to indicate the condition of the stop and start system when certain vehicle conditions are met.

Stop and Start System Condition Multi-information Display Message*1 Vehicle Condition
When the engine cannot be stopped by the stop and start system
V115706

*2
"Non-Dedicated Battery" A non-specified auxiliary battery for the stop and start system may have been installed.
"Battery Charging"
·

The auxiliary battery charge amount may be low.

·

A refresh charge may be occurring.


"Stop & Start system Unavailable"
·

The engine may have been started with the hood opened.

·

The stop and start system is temporarily disabled.


"In Preparation"
·

The brake booster load decreased.

·

The vehicle is operated at a high elevation.


"For Climate Control"
·

The air conditioning system is being used when the ambient temperature is high or low.

·

Windshield defogger is pressed.


When the engine automatically restarts while stopped by the stop and start system
V115706

*2
"For Climate Control"
·

The air conditioning system is turned on or the air conditioning is being used.

·

Windshield defogger is turned on.


"Battery Charging" The auxiliary battery charge amount may be low.
When the engine cannot be restarted by the stop and start system - "Stop & Start System active. Shift to N and Press Clutch to Restart" The shift lever has been shifted from neutral to another position with the clutch pedal released.
The system may be malfunctioning - "Stop & Start System Malfunction Visit Your Dealer" -

HINT:
·

*1: Messages are listed in the order of priority.

·

*2: When the engine cannot be stopped by the stop and start system or the engine is restarted while the engine is stopped by the stop and start system, the following mark is displayed on the multi-information display.




STOP AND START SYSTEM OPERATION


Depending on the type of malfunction, stop and start control may be prohibited by the fail-safe function. The following table shows effects on the vehicle and areas to be inspected when there is a malfunction in the stop and start system.

Malfunctioning Area Malfunction DTC Output Data List / Freeze Frame Data Effect on Vehicle Area to be Inspected
IGSW circuit Open P253014 IG Switch
·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


Wire harness or connector
+B circuit Open - Data List cannot be checked because power not supplied to the engine stop and start ECU Stop and start control prohibited Wire harness or connector
TMN (neutral position switch) circuit Open P085015
·

Neutral Switch

·

N Position Switch Signal Voltage


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Neutral position switch


Shorted
·

P085011

·

P085015


·

Neutral Switch

·

N Position Switch Signal Voltage


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


CLL (clutch switch assembly) circuit Stuck on P186262
P083011
·

Clutch Lower SW

·

N/Clutch Lower Switch Malfunction

·

N/Clutch Upper Switch Malfunction


·

Stop and start control prohibited

·

Stop and start cancel indicator light blinks


·

Wire harness or connector

·

Clutch switch assembly


Stuck off -
·

Clutch Lower SW

·

N/Clutch Lower Switch Malfunction

·

N/Clutch Upper Switch Malfunction


Stop and start control prohibited
BNT1 (engine hood courtesy switch) circuit Stuck on - Hood Courtesy Switch The engine does not stall when the engine hood is opened with the shift lever in neutral while the engine is stopped by stop and start control
·

Wire harness or connector

·

Engine hood courtesy switch (hood lock assembly)


Stuck off - Stop and start control prohibited despite engine hood being closed
ECAN (stop and start system cancel switch (combination switch assembly)) circuit Stuck on - Stop&Start Cancel Switch Stop and start control prohibited
·

Wire harness or connector

·

Stop and start system cancel switch (combination switch assembly)


Stuck off - Stop and start control cannot be canceled by pressing the stop and start system cancel switch (combination switch assembly)
BRVC/PB/BRE2 (vacuum sensor) circuit Open P055515 Brake Boost Pressure
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

Wire harness or connector

·

Vacuum sensor assembly

·

Brake booster assembly

·

Vacuum hose


Shorted
·

P055511

·

P055515


Remains at intermediate value
·

P055500

·

P05552A


STA circuit Overcurrent P061519 -
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Wire harness or connector

·

ST NO. 1 relay

·

Engine stop and start ECU


Stuck on P164400
·

Wire harness or connector

·

ST NO. 1 relay

·

Engine stop and start ECU


Stuck off P164400
BBC (backup boost converter) circuit Overcurrent P323A19 State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Auxiliary battery

·

ECUs and sensors connected to B41, B42, B43 and IG41


·

Open

·

Shorted

·

Internal circuit malfunction

·

Auxiliary battery


·

P30DF62

·

P30EF4B

·

P323A00

·

P323A16

·

P323AA2

·

P323B29

·

P323B38


State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Auxiliary battery


ECU inner circuit Malfunction P16449E -
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


Engine stop and start ECU
Monitoring CPU circuit Malfunction P060629 State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


Engine stop and start ECU
Crankshaft position sensor circuit Open P033562
·

Engine Speed (ECM)

·

Engine Speed


Stop and start control prohibited
·

Wire harness or connector

·

Crankshaft position sensor



Effects on Vehicle due to Related System Malfunctions
Malfunctioning Area Malfunction DTC Output Data List / Freeze Frame Data Effect on Vehicle Area to be Inspected
SFI system MIL illuminated DTCs for SFI system output
·

Stop&Start Operating Permission (ECM 1)

·

Stop&Start Operating Permission (ECM 2)


Stop and start control prohibited SFI system
Abnormal NE signal DTCs for SFI system output -
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

SFI system (crankshaft position sensor circuit)

·

Wire harness or connector


Crankshaft reverse rotation detection DTCs for SFI system output -
·

Stop and start control prohibited

·

MIL illuminated


SFI system (crankshaft position sensor circuit)
Charging system Battery state sensor assembly malfunction Charging system DTCs output
·

Battery Fluid Temperature

·

Integrated Current


Stop and start control prohibited Charging system
Electronically controlled brake system ABS running - ABS Running Stop and start control prohibited -
Malfunction in wheel speed sensor Brake control system DTCs output
·

Vehicle Speed

·

Wheel Speed Malfunction


Stop and start control prohibited
·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)

·

Vehicle speed sensor


Power steering system Malfunction in power steering system EPS assist current value invalid
·

EPS Load


Stop and start control prohibited
·

Power steering ECU

·

Torque sensor


Seat belt warning system Malfunction in seat belt warning system - Driver Seat Belt Buckle Switch
·

Stop and start control prohibited (stuck off)

·

Engine does not restart when it is stopped by stop and start control (stuck on)


·

Front seat inner belt assembly LH

·

Wire harness or connector


Driver door courtesy light switch circuit Malfunction in driver door courtesy light switch circuit - Driver Courtesy Switch Signal
·

Stop and start control prohibited (stuck off)

·

Engine does not restart when it is stopped by stop and start control (stuck on)

·

Stop and start indicator blinks

·

Sounds the warning buzzer


·

Front door courtesy light switch assembly LH

·

Driver door courtesy light switch circuit


Air conditioning system Malfunction in ambient temperature sensor Air conditioning system DTCs output Ambient Temperature Stop and start control prohibited Ambient temperature sensor circuit
Brake vacuum Brake booster vacuum drops -
·

Brake Boost Pressure

·

Brake Negative Pressure


Stop and start control prohibited
·

Brake booster assembly vacuum

·

Brake booster assembly

·

Vacuum sensor assembly

·

Vacuum hose


Power source Backup boost converter malfunction
·

P30DF62

·

P30EF4B

·

P323A00

·

P323A16

·

P323AA2

·

P323B29

·

P323B38


State of BBC
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

BBC NO. 1 fuse

·

BBC NO. 2 fuse

·

Wire harness or connector

·

Engine stop and start ECU

·

Auxiliary battery


Charging system malfunction - Alternator Status Stop and start control prohibited Charging system
Charging control system P160F00 -
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


Charging system
Number of starter operations Exceeds the specified limit P154563
·

Starter Operation #

·

Number of Engine Starts (IG-ON)

·

Number of Engine Starts (Stop & Start)


·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

Starter assembly replacement is required

·

ST NO. 1 relay replacement is required

·

Fuse replacement is required


Starter signal malfunction Signal does not match with the starter switch P061562
·

Starter

·

Engine Starter Signal


·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

Wire harness or connector

·

Engine stop and start ECU


Jump start Engine started with the engine hood open - Stop&Start Operating Prohibition (Jump Start) Stop and start control prohibited
(permitted when the ignition switch is turned off)
·

Check for history of roadside service or jump start due to dead auxiliary battery

·

Engine hood courtesy switch (hood lock assembly)


CAN communication Communication interrupted
·

U010087

·

U012687

·

U012987

·

U013187

·

U014087

·

U015187

·

U015587

·

U016487

·

U117087


-
·

Stop and start control prohibited

·

Stop and start cancel indicator blinks


·

Applicable wire harness or connector

·

Applicable ECU