Home › Vehicle Exterior › WIPER / WASHER › RAIN SENSOR › from 2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0482415 RAIN SENSOR G

WIPER / WASHER  RAIN SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89941 1.INSPECT RAIN SENSOR

Pre-procedure1

a.

Remove the rain sensor cover.


b.

Disconnect the rain sensor connector.


Procedure1

a.
E267170C99
1.458,0.375 1.875,0.625 0.417,0.25 1.979,1.375 2.479,1.677 true 1.531,1.354 1.021,1.688 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 0.781,1.698 1.094,1.896 0.313,0.198 10 false ES 2.521,1.688 2.885,1.885 0.365,0.198 10 false SIG 1.583,0.417 1.948,0.615 0.365,0.198 10 false V9
*a Front view of wire harness connector
(to Rain sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

V9-4 (SIG) - V9-2 (ES) Ignition switch ON 11 to 14 V


If the result is not as specified, repair or replace the harness or connector.


Post-procedure1

a.

None.


Pre-procedure2

a.

None.


Procedure2

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

V9-2 (ES) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


Post-procedure2

a.

None.


Pre-procedure3

a.

Reconnect the rain sensor connector.


b.

Connect an oscilloscope to the rain sensor connector.


Procedure3

a.
E257042C37
1.5,0.146 1.917,0.396 0.417,0.25 1.604,0.927 1.167,0.51 true 1.833,0.927 2.26,0.542 true 0.083,0.073 0.313,0.26 0.229,0.188 10 false *a 2.333,0.469 2.792,0.625 0.458,0.156 10 false ES 0.823,0.448 1.333,0.604 0.51,0.156 10 false MPX 1.906,0.885 2.229,1.063 0.323,0.177 10 false 1 1.76,0.885 2.083,1.063 0.323,0.177 10 false 2 1.604,0.885 1.927,1.063 0.323,0.177 10 false 3 1.438,0.885 1.76,1.063 0.323,0.177 10 false 4 1.625,0.198 2.021,0.417 0.396,0.219 10 false V9
*a Component with harness connected
(Rain sensor)


Check for pulses.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(V9)Location & Routing

Click Connector(V9)Body>No. 1 Roof Wire>Rain Sensor

V9-3 (MPX) - V9-2 (ES) Ignition switch ON
Front wiper switch Auto
Pulse generation


If the result is not as specified, replace the rain sensor.


Post-procedure3

a.

Install the rain sensor cover.