1.INSPECT SHIFT LOCK CONTROL ECU (w/ Entry and Start System)
If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.
Disconnect the shift lock control ECU connector.
Inspect the wire harness.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H20)Location & Routingewd_type=routing;type=c;code=H20 Click Connector(H20)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H20;pinno=5 |
||
| H20-5(IG) - Body ground | Ignition switch ON | 11 to 14 V |
| H20-5(IG) - Body ground | Ignition switch off | Below 1 V |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H20)Location & Routingewd_type=routing;type=c;code=H20 Click Connector(H20)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H20;pinno=4 |
||
| H20-4(STP) - Body ground | Ready ON, brake pedal depressed | 11 to 14 V |
| H20-4(STP) - Body ground | Ready ON, brake pedal released | Below 1 V |
If the result is not as specified, repair or replace the wire harness or connector or replace the hybrid vehicle control ECU assembly.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H20)Location & Routingewd_type=routing;type=c;code=H20 Click Connector(H20)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H20;pinno=1 |
||
| H20-1(E) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
Disconnect the shift lock solenoid connector.
Inspect shift lock solenoid:
| *a | Front view of wire harness connector
(to Shift Lock Solenoid) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4(P) - A-3(E2) | Shift lever in P | 10 kΩ or higher |
| A-4(P) - A-3(E2) | Shift lever not in P | Below 1 Ω |
| A-1(SLS+) - A-2(SLS-) | Always | 112 Ω |
If the result is not as specified, replace the shift lock control unit assembly.
2.INSPECT SHIFT LOCK CONTROL ECU (w/o Entry and Start System)
If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.
Disconnect the shift lock control ECU connector.
Inspect the wire harness.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H19)Location & Routingewd_type=routing;type=c;code=H19 Click Connector(H19)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H19;pinno=1,4 |
||
| H19-1(ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| H19-1(ACC) - Body ground | Ignition switch off | Below 1 V |
| H19-4(IG) - Body ground | Ignition switch ON | 11 to 14 V |
| H19-4(IG) - Body ground | Ignition switch off | Below 1 V |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H19)Location & Routingewd_type=routing;type=c;code=H19 Click Connector(H19)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H19;pinno=8 |
||
| H19-8(STP) - Body ground | Ignition switch ON, brake pedal depressed | 11 to 14 V |
| H19-8(STP) - Body ground | Ignition switch ON, brake pedal released | Below 1 V |
If the result is not as specified, repair or replace the wire harness or connector or replace the hybrid vehicle control ECU assembly.
| *a | Front view of wire harness connector
(to Shift Lock Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H19)Location & Routingewd_type=routing;type=c;code=H19 Click Connector(H19)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H19;pinno=7 |
||
| H19-7(E) - Body ground | Always | Below 1 Ω |
If the result is not as specified, repair or replace the shift lock control ECU wire harness.
Connect the shift lock control ECU connector.
Inspect key interlock solenoid operation signal:
| *a | Component with harness connected
(Shift Lock Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H19)Location & Routingewd_type=routing;type=c;code=H19 Click Connector(H19)Instrument Panel>Instrument Panel Wire / Speaker Wire>Shift Lock Control Unit Assemblyewd_type=component;type=c;code=H19;pinno=5 |
||
| H19-5(KLS+) - Body ground | Ignition switch ACC and shift lever in P | Below 1 V |
| H19-5(KLS+) - Body ground | Ignition switch ACC and shift lever not in P | 11 to 14 V |
Do not disconnect the shift lock control ECU connector.
If the result is not as specified, replace the shift lock control unit assembly.
Disconnect the shift lock solenoid connector.
Inspect shift lock solenoid:
| *a | Front view of wire harness connector
(to Shift Lock Solenoid) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4(P) - A-3(E2) | Shift lever in P | 10 kΩ or higher |
| A-4(P) - A-3(E2) | Shift lever not in P | Below 1 Ω |
| A-1(SLS+) - A-2(SLS-) | Always | 112 Ω |
If the result is not as specified, replace the shift lock control unit assembly.