Home › Drivetrain › EC6D (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › from 2021.07
RM3700E _52 Drivetrain _104886 EC6D MANUAL TRANSMISSION / TRANSAXLE _0482438 MANUAL TRANSAXLE SYSTEM J

EC6D MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  Pattern Select Switch iMT Mode Circuit  


DESCRIPTION

When the iMT switch (combination switch assembly) is operated to turn the iMT system on, the iMT indicator (green) in the combination meter assembly illuminates.

When the iMT indicator (green) is illuminated, the iMT system is in standby.

WIRING DIAGRAM

C290726E52
2.26,1.51 3.26,1.74 1,0.229 10 false H18 2.24,1.677 4.125,2.417 1.885,0.74 10 false Combination Switch Assembly (iMT Switch) 5.927,1.844 6.385,2.042 0.458,0.198 10 false A54 5.927,1.99 6.344,2.542 0.417,0.552 10 false ECM 6.229,0.74 6.844,0.938 0.615,0.198 10 false 12 V 5.573,0.906 6.188,1.104 0.615,0.198 10 false MTMS 5.323,0.906 5.563,1.115 0.24,0.208 10 false 38 4.042,0.875 4.323,1.135 0.281,0.26 10 false 8 2.167,0.896 2.625,1.25 0.458,0.354 10 false 5 2.344,0.896 3.344,1.125 1,0.229 10 false E 3.75,0.875 4.115,1.115 0.365,0.24 10 false IG

PROCEDURE

1.READ VALUE USING GTS (iMT SW)
a.

Enter the following menus:


b.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
iMT SW iMT switch (combination switch assembly) status ON or OFF
·

ON: iMT switch (combination switch assembly) being pushed

·

OFF: iMT switch (combination switch assembly) not being pushed


-
Powertrain > Engine > Data List
Tester Display
iMT SW
50003 372 570

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT COMBINATION SWITCH ASSEMBLY (iMT SWITCH)
2.INSPECT COMBINATION SWITCH ASSEMBLY (iMT SWITCH)
a.
C381674C64
1.417,0.167 1.917,0.417 0.5,0.25 0.74,1.427 1.333,1.427 true 2.094,1.427 2.688,1.427 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.75,1.323 3.219,1.521 0.469,0.198 10 false E 1.542,0.198 2,0.396 0.458,0.198 10 false H18 0.542,1.333 0.76,1.531 0.219,0.198 10 false IG
*a Component without harness connected
(Combination Switch Assembly (iMT Switch))


Remove the combination switch assembly.

Click hereDrivetrain>EC6D (MANUAL TRANSMISSION / TRANSAXLE)>INTELLIGENT MANUAL TRANSMISSION SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H18)Location & Routing

Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assembly

H18-8 (IG) - H18-5 (E) iMT switch (combination switch assembly) being pushed Below 1 Ω
H18-8 (IG) - H18-5 (E) iMT switch (combination switch assembly) not being pushed 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the H18 combination switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H18)Location & Routing

Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assembly

H18-5 (E) - Body ground Always Below 1 Ω



c.

Connect the H18 combination switch assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)

4.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A54)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

A54-38 (MTMS) - Body ground iMT switch (combination switch assembly) being pushed Below 50 Ω
A54-38 (MTMS) - Body ground iMT switch (combination switch assembly) not being pushed 10 kΩ or higher



c.

Connect the A54 ECM connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)