Home › General › MAINTENANCE › M15A-FKS OIL AND OIL FILTER › from 2021.07
RM3700E _V1 General _093024 MAINTENANCE _0442332 M15A-FKS OIL AND OIL FILTER A

MAINTENANCE  M15A-FKS OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 51443C 1.REMOVE REAR ENGINE UNDER COVER RH

a.
A458758

for TMC Made :

i.

Disengage the claw.


ii.

Remove the 2 screws and disengage the 3 guidesto remove the rear engine under cover RH.



b.
A485758

for TMMF Made :

i.

Remove the 4 screws and rear engine under cover RH.



Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Clean the oil pan drain plug.


d.

Install a new gasket to the oil pan drain plug.


e.

Install the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15601 3.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A464390E02
1.646,0.531 2.333,0.531 true 2.417,0.458 2.792,0.625 0.375,0.167 10 true SST

Using SST, remove the oil filter sub-assembly.

SST
09228-06502  


Hide 15601 4.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.
A458759N01
1.646,0.531 2.333,0.531 true 2.417,0.458 2.792,0.625 0.375,0.167 10 true SST

Using SST, tighten the oil filter sub-assembly.

SST
09228-06502  

i.

Depending on the work space available, choose from the following:

·

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.


Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)

·

If not enough space is available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or using a common wrench.




Hide 5.ADD ENGINE OIL

a.

Add new engine oil and install the oil filler cap sub-assembly.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SN " Resource-Conserving"or SN PLUS "Resource-Conserving" or SP "Resource-Conserving"; or ILSAC GF-6B multigrade engine oil
·

0W-16


API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving", SN PLUS "Resource-Conserving" or SP "Resource-Conserving"; or ILSAC GF-6A multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30



Standard Capacity:
Item Standard Condition
Drain and refill with oil filter change 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Drain and refill without oil filter change 3.2 liters (3.4 US qts, 2.8 Imp. qts)
Dry fill 4.3 liters (4.5 US qts, 3.8 Imp. qts)


Hide 6.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.


Hide 51443C 8.INSTALL REAR ENGINE UNDER COVER RH

a.
A485765C01
2.688,1.167 2.833,1 true 2.229,1.344 2.375,1.552 true 2.219,3.813 2.365,4.021 true 2.865,3.552 3.01,3.385 true 0.094,0.083 0.354,0.302 0.26,0.219 12 true *a 0.063,2.583 0.323,2.802 0.26,0.219 12 true *b 2.813,0.833 3.073,1.052 0.26,0.219 10 true *1 2.958,3.229 3.219,3.448 0.26,0.219 10 true *1 2.073,3.667 2.333,3.885 0.26,0.219 10 true *2 2.063,1.198 2.323,1.417 0.26,0.219 10 true *2
*1 Rear Engine Under Cover RH
*2 No. 1 Engine Under Cover Assembly
*a OK
*b NG


for TMC Made :

i.

Engage the 3 guides and claw to install the rear engine under cover RH as shown in the illustration.


ii.

Install the 2 screws.



b.

for TMMF Made :

i.

Install the rear engine under cover RH with the 4 screws.