FREEZE FRAME DATA/INFORMATION
Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED
Freeze Frame Data is stored when a DTC is output.
Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Check the Freeze Frame Data when a DTC is output.
Enter the following menus: Chassis / Brake Booster / Trouble Codes.
Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Select a DTC to display the Freeze Frame Data.
Check the Freeze Frame Data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0, Max.: 16777215 | - | - |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa, Max.: 23.99 MPa | Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| ECB Motor Relay | Motor relay operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Motor Relay2 | Motor relay 2 operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm, Max.: 255 mm | Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| Brake Pedal Stroke Change Speed | Brake pedal stroke rate of change | Min.: -2560 mm/s, Max.: 2540 mm/s | Brake pedal released or depressed and held: 0 mm/s | Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal |
| VCSK Voltage Value | VCSK voltage value | Min.: 0.000 V, Max.: 5.500 V | 4.800 to 5.200 V | - |
| +BS Voltage | +BS voltage value | Min.: 0.0 V, Max.: 25.5 V | - | Changes in proportion to auxiliary battery voltage |
| Stroke Sensor (DTS) CH1 SENT | Relative displacement sensor (brake booster with master cylinder assembly) CH1 SENT value | Min.: 0, Max.: 4095 | - | - |
| Stroke Sensor (DTS) CH2 PWM | Relative displacement sensor (brake booster with master cylinder assembly) CH2 PWM value | Min.: 0 %, Max.: 100 % | - | - |
| The Number of Capacitor Operation | The Number of Capacitor Operation | Min.: 0 Times, Max.: 255 Times | - | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0, Max.: 16777215 | - | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa, Max.: 23.99 MPa | Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| M/C Sensor Grade | Master cylinder pressure sensor change (value detected by ECU) | Min.: -30 MPa/s, Max.: 225 MPa/s | Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Lateral G | Lateral G | Min.: -25.105 m/s2, Max.: 24.908 m/s2 | Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2, Max.: 24.908 m/s2 | During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s, Max.: 127°/s | Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Value | Steering angle sensor | Min.: -3276.8°, Max.: 3276.7° | Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0° |
- |
| Zero Point of Steering Angle | Memorized zero point value of steering sensor | Min.: -3276.8°, Max.: 3276.7° | - | - |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Engine Revolutions | Engine speed | Min.: 0 rpm, Max.: 65535 rpm | Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%, Max.: 127.5% | Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Real Engine Torque | Real engine torque | Min.: -1024.000 Nm, Max.: 1023.000 Nm | - | - |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / VSC expert mode (VSC expert mode MID ON) / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode VSC expert mode (VSC expert mode MID ON): VSC expert mode VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode /
Pressure hold mode / Pressure release mode / EPB lock mode |
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | The value of the target oil pressure applied to the front brake RH | Min.: 0.0 MPa, Max.: 20.0 MPa | - | Operating the brake pedal: Varies depending on the target oil pressure |
| FL Target Oil Pressure | The value of the target oil pressure applied to the front brake LH | Min.: 0.0 MPa, Max.: 20.0 MPa | - | Operating the brake pedal: Varies depending on the target oil pressure |
| RR Target Oil Pressure | The value of the target oil pressure applied to the rear brake RH | Min.: 0.0 MPa, Max.: 20.0 MPa | - | Operating the brake pedal: Varies depending on the target oil pressure |
| RL Target Oil Pressure | The value of the target oil pressure applied to the rear brake LH | Min.: 0.0 MPa, Max.: 20.0 MPa | - | Operating the brake pedal: Varies depending on the target oil pressure |
| Vehicle Speed | Vehicle speed (vehicle speed used for each control) | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle speed grade | Min.: -25.105 m/s2, Max.: 24.908 m/s2 | Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During deceleration/acceleration: Changes continuously |
| Vehicle Stop Time from IG ON | Time vehicle stopped after ignition switch turned to ON | Min.: 0 s, Max.: 1275 s | - | - |
| Travel Distance from IG ON | Driving time after ignition switch turned to ON | Min.: 0 s, Max.: 1275 s | - | - |
| Downhill Assist Control/Crawl Control SW | Downhill assist control switch | OFF / ON | OFF: Downhill assist control switch OFF
ON: Downhill assist control switch ON |
for AWD |
| Stop Light SW | Stop light switch assembly (STP terminal input) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake switch assembly | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Reverse Position Switch | Reverse position switch status | OFF / ON | OFF: Shift lever position is not in R
ON: Shift lever position is in R |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (HZRI terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (Stop light switch assembly)
(STP2 terminal input) |
OFF / ON | OFF: Stop light control relay (Stop light switch assembly) OFF
ON: Stop light control relay (Stop light switch assembly) ON |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
|
| TRC(TRAC) Control | TRC control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC engine control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC brake control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: Not during control
Under Controlling: During control |
- |
| Fail Status | Fail Status | OFF / ON | OFF: Fail Status off
ON: Fail Status on |
- |
| Fail Control | Fail Control Status | OFF / ON | OFF: Fail Control off
ON: Fail Control on |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: Not during control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: Not during control
ON: During control |
w/ Pre-collision System |
| Stop Light Relay State for ECU Control | Stop light control relay (Stop light switch assembly) status (STPO terminal output) (for ECU control) | OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off (Stop light off)
ON: Stop light control relay (Stop light switch assembly) on (Stop light on) |
- |
| Solenoid State for ECU Control | ABS solenoid relay status (for ECU control) | OFF / ON | OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating |
- |
| Motor State for ECU Control | ABS motor relay status (for ECU control) | OFF / ON | OFF: ABS motor relay not operating
ON: ABS motor relay operating |
- |
| Operation History of IG OFF while Vehicle is moving | History of ignition switch turned off when vehicle is in motion | OFF / ON | OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| Regenerative Cooperation | Regenerative cooperation | OFF / ON | OFF: Not operating
ON: Operating |
- |
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF
ON: VSC OFF switch ON |
|
| Reservoir Warning SW | Brake fluid level warning switch | OFF / ON | OFF: Reservoir level normal
ON: Reservoir level low |
- |
| IGP_PT2 | IGP_PT2 status | OFF / ON | OFF: IGP_PT2 OFF
ON: IGP_PT2 ON |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel LH | Forward / Back | - | - |
| EFI Communication Open | EFI communication open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Open | Yaw rate sensor (airbag sensor assembly) open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Deceleration Open | Acceleration sensor (airbag sensor assembly) open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Steering Open | Steering sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm, Max.: 255 mm | Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| FR Regenerative Request | FR regenerative request torque | Min.: 0 Nm, Max.: 1048560 Nm | - | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| FR Regenerative Operation | FR regenerative operation torque | Min.: 0 Nm, Max.: 1048560 Nm | - | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| VCSK Voltage Value | VSK2 voltage value | Min.: 0.000 V, Max.: 5.500 V | 4.800 to 5.200 V | - |
| IGR Voltage | IGR voltage value (value detected by ECU) | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage |
| +BS Voltage | +BS voltage value | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| +BM Voltage | BM voltage value | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Stroke Sensor (APS) CH1 PWM | Brake pedal stroke sensor assembly CH1 PWM value | Min.: 0 %, Max.: 100 % | - | - |
| Stroke Sensor (APS) CH2 PWM | Brake pedal stroke sensor assembly CH2 PWM value | Min.: 0 %, Max.: 100 % | - | - |
*1: for entering inspection mode: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY
*2: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE
*3: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY
CLEAR FREEZE FRAME DATA
Clearing the DTCs will also clear the Freeze Frame Data.
Enter the following menus: Chassis / Brake Booster / Trouble Codes.
Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Press the DTC clear button.