Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C121F04  Electronic Brake Booster Control Module "A" System Internal Failure  


DESCRIPTION

If there is a malfunction in the power source circuit, the electric brake booster (brake booster with master cylinder assembly) stores a DTC, and ABS, brake assist, regenerative braking, etc. operation is prohibited by fail-safe control.

When a malfunction in the auxiliary battery, charging circuit, etc. results in a voltage differential between the +BS terminal and the internal circuit terminal of the electric brake booster (brake booster with master cylinder assembly), this DTC is stored.

When the voltage between the +BS terminal and the internal circuit terminal of the electric brake booster (brake booster with master cylinder assembly) returns to normal, this DTC is cleared.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C121F04 Electronic Brake Booster Control Module "A" System Internal Failure A voltage difference of 1.0 V or more is detected between the +BS terminal and the IGR terminal, and the voltage of the IGR terminal is 3.2 V or less. Electric brake booster (brake booster with master cylinder assembly) Brake Booster A

WIRING DIAGRAM

C443938E05
5.271,1.156 5.729,1.354 0.458,0.198 10 false A34 5.26,2.031 5.719,2.229 0.458,0.198 10 false A34 5.604,2.917 6.063,3.115 0.458,0.198 10 false A35 5.26,2.917 5.719,3.115 0.458,0.198 10 false A34 5.615,2.031 6.073,2.229 0.458,0.198 10 false A35 5.604,1.156 6.063,1.354 0.458,0.198 10 false A35 5.656,1.375 5.948,1.573 0.292,0.198 10 false *2 5.302,2.26 5.594,2.458 0.292,0.198 10 false *1 5.313,3.135 5.604,3.333 0.292,0.198 10 false *1 5.281,1.375 5.573,1.573 0.292,0.198 10 false *1 5.646,2.26 5.938,2.458 0.292,0.198 10 false *2 5.667,3.135 5.958,3.333 0.292,0.198 10 false *2 5.698,2.74 5.99,2.938 0.292,0.198 10 false 9 5.354,2.729 5.646,2.927 0.292,0.198 10 false 9 5.313,1.833 5.604,2.031 0.292,0.198 10 false 20 5.333,0.938 5.625,1.135 0.292,0.198 10 false 1 5.688,0.938 5.979,1.135 0.292,0.198 10 false 1 5.656,1.833 5.948,2.031 0.292,0.198 10 false 20 1.406,1.104 4.771,1.302 3.365,0.198 10 false from Auxiliary Battery 1.396,2.031 4.76,2.229 3.365,0.198 10 false from IGR-NO. 1 Relay 3.729,1.323 7.094,1.521 3.365,0.198 10 false ABS-MAIN 3.656,2.208 7.021,2.406 3.365,0.198 10 false ECU-IGR NO. 3 5.979,1.167 6.438,1.365 0.458,0.198 10 false +BS 5.979,2.052 6.438,2.25 0.458,0.198 10 false IGR 5.979,2.917 6.438,3.115 0.458,0.198 10 false GND 4.76,3.948 7.125,4.354 2.365,0.406 10 false Electric Brake Booster (Brake Booster with Master Cylinder Assembly) 0.25,3.531 1.938,3.729 1.688,0.198 10 false *1: for LHD 0.26,4.042 1.948,4.24 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the electric brake booster (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A34 electric brake booster (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A34)Location & Routing

Click Connector(A34)Engine Compartment>Engine Room Main Wire>Brake Booster Control ECU (Brake Booster with Master Cylinder Assembly)

A34-1 (+BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A34 electric brake booster (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A34)Location & Routing

Click Connector(A34)Engine Compartment>Engine Room Main Wire>Brake Booster Control ECU (Brake Booster with Master Cylinder Assembly)

A34-20 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A35)Location & Routing

Click Connector(A35)Engine Compartment>Engine Room Main Wire>Brake Booster Control ECU (Brake Booster with Master Cylinder Assembly)

A35-1 (+BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A35)Location & Routing

Click Connector(A35)Engine Compartment>Engine Room Main Wire>Brake Booster Control ECU (Brake Booster with Master Cylinder Assembly)

A35-20 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR