Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483557 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  U007488  Control Module Communication Bus "B" Off Bus Off  U010087  Lost Communication with ECM/PCM "A" Missing Message  U010187  Lost Communication with TCM Missing Message  U012587  Lost Communication With Multi-axis Acceleration Sensor Module Missing Message  U012687  Lost Communication with Steering Angle Sensor Module Missing Message  U013187  Lost Communication With Power Steering Control Module Missing Message  U014087  Lost Communication with Body Control Module Missing Message  U015187  Lost Communication with Restraints Control Module Missing Message  U030057  Internal Control Module Software Incompatibility Invalid / Incompatible Software Component  U115C87  Lost Communication with ECM/PCM "A" (ch5) Missing Message  U130857  Software Incompatibility with Pre-collision Control Module Invalid / Incompatible Software Component  U130957  Software Incompatibility with Clearance Warning Control Module Invalid / Incompatible Software Component  


DESCRIPTION

The skid control ECU (brake actuator assembly) communicates with the following ECUs and sensors via CAN communication.

·

ECM

·

TCM (ECM)

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Steering sensor

·

Power steering ECU assembly

·

Main body ECU (multiplex network body ECU)

·

Airbag sensor assembly

·

Clearance warning ECU assembly

·

Engine stop and start ECU*1

·

Forward recognition camera*2


*1: w/ Stop and Start System

*2: w/ Pre-collision System


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U007488 Control Module Communication Bus "B" Off Bus Off The +BS terminal voltage is between 9.6 and a 16.5 V and a bus OFF state occurs for 0.1 seconds or more. CAN communication system Brake/EPB B
U010087 Lost Communication with ECM/PCM "A" Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2 seconds or more.
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U010187 Lost Communication with TCM Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the TCM (ECM) for 2 seconds or more.
·

CAN communication system

·

TCM (ECM)

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U012587 Lost Communication With Multi-axis Acceleration Sensor Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate and acceleration sensor (airbag sensor assembly) cannot be received for 1 second or more.
·

CAN communication system

·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U012687 Lost Communication with Steering Angle Sensor Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering sensor cannot be received for 1 second or more.
·

CAN communication system

·

Steering sensor

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U013187 Lost Communication With Power Steering Control Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the power steering ECU assembly cannot be received for 2 seconds or more.
·

CAN communication system

·

Power steering ECU assembly

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U014087 Lost Communication with Body Control Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, data cannot be received from main body ECU (multiplex network body ECU) continuously for 2 seconds or more.
·

CAN communication system

·

Main body ECU (multiplex network body ECU)

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U015187 Lost Communication with Restraints Control Module Missing Message The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the airbag sensor assembly cannot be received for 5 seconds or more.
·

CAN communication system

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U030057 Internal Control Module Software Incompatibility Invalid / Incompatible Software Component Engine information sent from the Engine stop and start ECU does not match that stored in the skid control ECU (brake actuator assembly).
·

CAN communication system

·

Engine stop and start ECU

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U115C87 Lost Communication with ECM/PCM "A" (ch5) Missing Message 'When the voltage at terminal +BS is between 9.6 and 16.5 V, data sent between the skid control ECU (brake actuator assembly) and the ECM cannot be received for 2 seconds or more.
·

CAN communication system

·

ECM

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U130857 Software Incompatibility with Pre-collision Control Module Invalid / Incompatible Software Component Pre-collision system information sent from the forward recognition camera does not match that stored in the skid control ECU (brake actuator assembly).
·

CAN communication system

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)


Brake/EPB B
U130957 Software Incompatibility with Clearance Warning Control Module Invalid / Incompatible Software Component 'When the voltage at terminal +BS is between 9.6 and 16.5 V, data sent between the skid control ECU (brake actuator assembly) and the clearance warning ECU assembly cannot be received for 2 seconds or more.
·

CAN communication system

·

Clearance warning ECU assembly

·

Skid control ECU (brake actuator assembly)


Brake/EPB B

PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

c.

Turn the ignition switch off.



NEXT

2.CHECK DTC OUTPUT (HEALTH CHECK)
2.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


Result:
Result Proceed to
DTCs for related systems are output together with DTC U007488, U010087, U010187, U012587, U012687, U013187, U014087, U015187, U030057, U115C87, U130875 or U130957. A
U007488, U010087, U010187, U012587, U012687, U013187, U014087, U015187, U030057, U115C87, U130875 or U130957 is output. B
DTCs are not output. C



A

GO TO DIAGNOSTIC TROUBLE CODE CHART (RELATED SYSTEM)

B

C