This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.
If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is set.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B157011 | Indicator (Red) Circuit Short to Ground | Manual (SOS) switch indicator (red) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telephone transceiver assembly ·
Map light assembly ·
Harness or connector |
Telematics | A |
| B157013 | Indicator (Red) Circuit Open | Manual (SOS) switch indicator (red) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telephone transceiver assembly ·
Map light assembly ·
Harness or connector |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Before replacing the telematics transceiver assembly, refer to Service Bulletin.
If DTC B157011 or B157013 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B157011 or B157013 is output | B |
| None of the above conditions are met | C |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect a positive (+) lead from the batteries to terminal 13 (IND1) and a negative (-) lead to terminal 16 (GND3) of the map light assembly (manual (SOS) switch) connector.
Procedure1
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Check if the manual (SOS) switch indicator (red) illuminates.
Manual (SOS) switch indicator (red) illuminates.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V6 map light assembly (manual (SOS) switch) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V6)Location & Routingewd_type=routing;type=c,c;code=H85,V6 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=4,3 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=13,16 |
||
| H85-4 (IND1) - V6-13 (IND1) | Always | Below 1 Ω |
| H85-4 (IND1) or V6-13 (IND1) - Body ground | Always | 10 kΩ or higher |
| H85-3 (SIG-) - V6-16 (GND3) | Always | Below 1 Ω |
| H85-3 (SIG-) or V6-16 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT