If the telephone transceiver assembly detects an error in the communication between the telephone transceiver assembly and the map light assembly (manual (SOS) switch) as a result of the telephone transceiver assembly self check, this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C511 | Emergency Call Switch Circuit Short to Ground | Manual (SOS) switch impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Map light assembly ·
Harness or connector ·
Telephone transceiver assembly |
Telematics | A |
| B15C513 | Emergency Call Switch Circuit Open | Manual (SOS) switch impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Map light assembly ·
Harness or connector ·
Telephone transceiver assembly |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Before replacing the telematics transceiver assembly, refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B15C511 or B15C513 is output | B |
| None of the above conditions are met | C |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Procedure1
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=12,16 |
||
| V6-12 (SIG1) - V6-16 (GND3) | Manual (SOS) switch not operated | 407.8 to 416.1 Ω |
| V6-12 (SIG1) - V6-16 (GND3) | Manual (SOS) switch operated | 81.1 to 82.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H85 telephone transceiver assembly connector.
Procedure1
Disconnect the V6 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V6)Location & Routingewd_type=routing;type=c,c;code=H85,V6 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=21,3 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=12,16 |
||
| H85-21 (SIG1) - V6-12 (SIG1) | Always | Below 1 Ω |
| H85-3 (SIG-) - V6-16 (GND3) | Always | Below 1 Ω |
| H85-21 (SIG1) or V6-12 (SIG1) - Body ground | Always | 10 kΩ or higher |
| H85-3 (SIG-) or V6-16 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT