If there is an open in a speaker circuit, the telephone transceiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the telephone transceiver assembly or front No. 4 speaker assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1AC07F | Speaker Cable Connection Actuator Stuck Off | The malfunction is detected in the telephone speaker circuit for approximately 10 seconds or more. | ·
Front No. 4 speaker assembly ·
Telephone transceiver assembly ·
Harness or connector |
Telematics | A |
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Before replacing the telematics transceiver assembly, refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B1AC07F is output | B |
| None of the above conditions are met | C |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
Disconnect the I1 front No. 4 speaker assembly connector.
Disconnect the H84 telephone transceiver assembly connector.
Procedure1
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(I1,H84)Location & Routingewd_type=routing;type=c,c;code=I1,H84 Click Connector(I1)Instrument Panel>No. 2 Instrument Panel Wire>No. 4 Front Speaker Assemblyewd_type=component;type=c;code=I1;pinno=4,2 Click Connector(H84)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H84;pinno=3,4 |
||
| I1-4 (+) - H84-3 (SPO+) | Always | Below 1 Ω |
| I1-2 (-) - H84-4 (SPO-) | Always | Below 1 Ω |
| I1-4 (+) or H84-3 (SPO+) - Body ground | Always | 10 kΩ or higher |
| I1-2 (-) or H84-4 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the front No. 4 speaker assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B1AC07F is output | B |
| None of the above conditions are met | C |
Post-procedure1
None
A
B
C
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DIAGNOSTIC TROUBLE CODE CHART
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT