Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE ACTUATOR (for TMMF Made 2WD) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0483915 ELECTRIC PARKING BRAKE ACTUATOR(for TMMF Made 2WD) G

PARKING BRAKE  ELECTRIC PARKING BRAKE ACTUATOR(for TMMF Made 2WD)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 46310B 1.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY (for Gasoline Model)

HINT:

Using the GTS to perform the Utilities allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Utilities early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Utilities.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Brake/EPB / Utility.


f.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.


g.

According to the display on the tester, perform the Utility.

Chassis > Brake/EPB > Utility
Tester Display
EPB Control Switch
50005 435 4556
OK:
Tester Display Condition of the Rear Tire
Lock Lock
Release Free


i.

If the result is not as specified, inspect the electric parking brake actuator.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMMF Made 2WD)>INSPECTION



h.

Turn the ignition switch to ON, pull the electric parking brake switch to the lock side for 1 second and check that the parking brake indicator light (red) illuminates.


i.

Push the electric parking brake switch to the release side for 1 second and check that the parking brake indicator light (red) turns off.


j.

Also, check that the brake warning light / yellow (minor malfunction) does not illuminate at this time.


Hide 46310B 2.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY (for HV Model)

HINT:

Using the GTS to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Uilities.


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Utility.


f.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.


g.

According to the display on the tester, perform the Utility.

Chassis > Electric Parking Brake > Utility
Tester Display
EPB Control Switch
50005 485 4556
OK:
Tester Display Condition of the Rear Tire
Lock Lock
Release Free


i.

If the result is not as specified, inspect the electric parking brake actuator.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMMF Made 2WD)>INSPECTION



h.

Turn the ignition switch to ON, pull the electric parking brake switch to the lock side for 1 second and check that the parking brake indicator light (red) illuminates.


i.

Push the electric parking brake switch to the release side for 1 second and check that the parking brake indicator light (red) turns off.


j.

Also, check that the brake warning light / yellow (minor malfunction) does not illuminate at this time.