Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0483555 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMMF Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMMF Made)  P085013  Neutral Switch Circuit Open  P18301C  Neutral Switch Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

This DTC is stored when an abnormal neutral position switch signal is detected by the skid control ECU (brake actuator assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
P085013 Neutral Switch Circuit Open
·

Diagnosis Condition:

-

·

Malfunction Status: (One of the following conditions is met):

Abnormal neutral position switch power supply voltage and +BS terminal voltage

Open or short in neutral position switch circuit

·

Detection Time:

0.1 seconds or more


·

Neutral position switch

·

Wire harness or connector

·

Stop and start system*1

·

ECM*2


DTC stored Brake/EPB B An electric parking brake system malfunction is displayed on the multi-information display.
P18301C Neutral Switch Supply Voltage Circuit Voltage Out of Range
·

Diagnosis Condition:

-

·

Malfunction Status: (One of the following conditions is met):

Abnormal neutral position switch power supply voltage and +BS terminal voltage

Open or short in neutral position switch circuit

·

Detection Time:

0.1 seconds or more


·

Neutral position switch

·

Wire harness or connector

·

Stop and start system*1

·

ECM*2


DTC stored Brake/EPB B An electric parking brake system malfunction is displayed on the multi-information display.

*1: w/ Stop and Start System

*2: w/o Stop and Start System


DTC Detection Conditions P085013
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status Neutral position switch open circuit is detected ○ - -
Neutral position switch short circuit is detected - ○ -
Neutral position switch power supply voltage and +BS terminal voltage are judged to be abnormal - - ○
Detection Time 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions P18301C
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status Neutral position switch open circuit is detected ○ - -
Neutral position switch short circuit is detected - ○ -
Neutral position switch power supply voltage and +BS terminal voltage are judged to be abnormal - - ○
Detection Time 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more
Number of Trips 1 trip 1 trip 1 trip

WIRING DIAGRAM

w/ Stop and Start System


C409389E03
0.958,2.094 1.271,2.292 0.313,0.198 10 false IC 2.323,1.115 2.646,1.354 0.323,0.24 10 false W1 2.26,1.99 2.708,2.198 0.448,0.208 10 false TMN 2.385,2.865 2.729,3.052 0.344,0.188 10 false F+ 2.656,1.115 2.885,1.292 0.229,0.177 10 false 1 2.656,1.99 2.885,2.167 0.229,0.177 10 false 2 2.677,2.875 2.906,3.052 0.229,0.177 10 false 3 0.75,3.49 1.219,3.677 0.469,0.188 10 false D44 0.76,3.646 2.427,3.875 1.667,0.229 10 false Neutral Position Switch 5.417,3.813 5.885,4 0.469,0.188 10 false A39 5.417,4 6.979,4.479 1.563,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 3.094,1.104 3.323,1.281 0.229,0.177 10 false 26 3.177,1.99 3.406,2.167 0.229,0.177 10 false 8 3.115,2.875 3.344,3.052 0.229,0.177 10 false 25 3.427,1.104 3.969,1.313 0.542,0.208 10 false TMVC 3.417,1.99 3.958,2.198 0.542,0.208 10 false TMN 3.417,2.875 3.958,3.083 0.542,0.208 10 false TME2 3.25,3.813 3.719,4 0.469,0.188 10 false A67 3.25,3.979 5.063,4.229 1.813,0.25 10 false Engine Stop and Start ECU


w/o Stop and Start System


C409389E05
0.958,2.094 1.271,2.292 0.313,0.198 10 false IC 2.323,1.115 2.646,1.354 0.323,0.24 10 false W1 2.26,1.99 2.708,2.198 0.448,0.208 10 false TMN 2.385,2.865 2.729,3.052 0.344,0.188 10 false F+ 2.656,1.115 2.885,1.292 0.229,0.177 10 false 1 2.656,1.99 2.885,2.167 0.229,0.177 10 false 2 2.677,2.875 2.906,3.052 0.229,0.177 10 false 3 0.75,3.49 1.219,3.677 0.469,0.188 10 false D44 0.76,3.646 2.427,3.875 1.667,0.229 10 false Neutral Position Switch 5.417,3.813 5.885,4 0.469,0.188 10 false A39 5.417,4 6.979,4.479 1.563,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 3.094,1.104 3.323,1.281 0.229,0.177 10 false 83 3.063,1.99 3.604,2.219 0.542,0.229 10 false 106 3.115,2.875 3.583,3.094 0.469,0.219 10 false 60 3.427,1.104 3.969,1.313 0.542,0.208 10 false VCNP 3.417,1.99 3.958,2.198 0.542,0.208 10 false NPSW 3.417,2.875 3.958,3.083 0.542,0.208 10 false ENPS 3.802,3.813 4.271,4 0.469,0.188 10 false D51 3.802,3.979 5.615,4.229 1.813,0.25 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.


PROCEDURE

1.CHECK VEHICLE
a.

Check the vehicle specification.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

2.CHECK DTC (STOP AND START SYSTEM)

B

3.READ VALUE USING GTS (NEUTRAL POSITION SWITCH)
2.CHECK DTC (STOP AND START SYSTEM)
a.

Check for DTCs in the stop and start system.

HINT:

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


Powertrain > Stop and Start > Trouble Codes
50001 392

Result:
Proceed to
NEXT



NEXT

GO TO STOP AND START SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

3.READ VALUE USING GTS (NEUTRAL POSITION SWITCH)
a.

Enter the following menus: Powertrain / Engine / Data List / Neutral Position Switch.

Powertrain > Engine > Data List
Tester Display
Neutral Position Switch
50003 372 881

b.

Read the value when the shift lever is in neutral and any other position.

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in neutral ON
Shift lever in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR
4.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


Pre-procedure1

a.

Disconnect the D44 neutral position switch connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D44)Location & Routing

Click Connector(D44)Engine Compartment>Engine Wire>Neutral Position Switch

D44-1 (W1) - Body ground Ignition switch ON 4.5 to 5.5 V
D44-2 (TMN) - Body ground Ignition switch ON 3.0 to 5.0 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

5.CHECK HARNESS AND CONNECTOR
5.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off and wait for at least 30 seconds.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D44)Location & Routing

Click Connector(D44)Engine Compartment>Engine Wire>Neutral Position Switch

D44-1 (W1) - D44-2 (TMN) Ignition switch off 0.95 to 1.05 kΩ
D44-3 (F+) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

6.CHECK HARNESS AND CONNECTOR (ECM - NEUTRAL POSITION SWITCH)
6.CHECK HARNESS AND CONNECTOR (ECM - NEUTRAL POSITION SWITCH)

Pre-procedure1

a.

Disconnect the D51 ECM connector.


b.

Disconnect the D44 neutral position switch connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D51,D44)Location & Routing

Click Connector(D51)Engine Compartment>Engine Wire>ECM

Click Connector(D44)Engine Compartment>Engine Wire>Neutral Position Switch

D51-83 (VCNP) - D44-1 (W1) Always Below 1 Ω
D51-60 (ENPS) - D44-3 (F+) Always Below 1 Ω
D51-106 (NPSW) - D44-2 (TMN) Always Below 1 Ω
D51-83 (VCNP) or D44-1 (W1) - Body ground Always 10 kΩ or higher
D51-60 (ENPS) or D44-3 (F+) - Body ground Always 10 kΩ or higher
D51-106 (NPSW) or D44-2 (TMN) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR