The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Map light assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
Telematics transceiver* ·
Harness or connector |
Navigation System | A |
*: w/ Telematics Transceiver
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for TMMF Made without Telematics Transceiver | A |
| for TMMF Made with Telematics Transceiver | B |
| for TMC Made without Telematics Transceiver | C |
| for TMC Made with Telematics Transceiver | D |
A
B
C
D
Pre-procedure1
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V6)Location & Routingewd_type=routing;type=c,c;code=H80,V6 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25,22 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,4 |
||
| H80-25 (SNS2) - V6-5 (SNS2) | Always | Below 1 Ω |
| H80-22 (MIN-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V6-5 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the MC telephone microphone assembly connector.
Procedure1
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,4 |
||
| V6-5 (SNS2) - V6-4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
Procedure1
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,4 |
||
| V6-5 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-5 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V6)Location & Routingewd_type=routing;type=c,c;code=H80,V6 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5 |
||
| H80-25 (SNS2) - V6-5 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H85 telematics transceiver connector.
Disconnect the V6 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V6)Location & Routingewd_type=routing;type=c,c;code=H85,V6 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=7 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=4 |
||
| H85-7 (MCI-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H85-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the telematics transceiver with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
Procedure1
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=7 |
||
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Procedure1
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,4 |
||
| V6-5 (SNS2) - V6-4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Procedure1
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,4 |
||
| V6-5 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-5 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V7)Location & Routingewd_type=routing;type=c,c;code=H80,V7 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25,22 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,14 |
||
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-22 (MIN-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the MC telephone microphone assembly connector.
Procedure1
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,14 |
||
| V7-13 (SNS2) - V7-14 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
Procedure1
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,14 |
||
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V7)Location & Routingewd_type=routing;type=c,c;code=H80,V7 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13 |
||
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H85 telematics transceiver connector.
Disconnect the V7 map light assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V7)Location & Routingewd_type=routing;type=c,c;code=H85,V7 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=14 |
||
| H85-7 (MCI-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H85-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component with harness connected
(Telematics Transceiver) |
Remove the telematics transceiver with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=7 |
||
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Procedure1
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,14 |
||
| V7-13 (SNS2) - V7-14 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
| *a | Component without harness connected
(Map Light Assembly) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,14 |
||
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG