The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the telematics transceiver sends power to telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the telematics transceiver.*
*: w/ Telematics Transceiver
for TMMF Made without Telematics Transceiver
for TMMF Made with Telematics Transceiver
for TMC Made without Telematics Transceiver
for TMC Made with Telematics Transceiver
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for TMMF Made without Telematics Transceiver | A |
| for TMMF Made with Telematics Transceiver | B |
| for TMC Made without Telematics Transceiver | C |
| for TMC Made with Telematics Transceiver | D |
A
B
C
D
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V6)Location & Routingewd_type=routing;type=c,c;code=H80,V6 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25,23,21,22,24 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,2,3,4 |
||
| H80-25 (SNS2) - V6-5 (SNS2) | Always | Below 1 Ω |
| H80-23 (MACC) - V6-2 (MACC) | Always | Below 1 Ω |
| H80-21 (MIN+) - V6-3 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V6-5 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-23 (MACC) or V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| H80-21 (MIN+) or V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V6 map light assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=23 |
||
| H80-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=24,22 |
||
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V6 map light assembly connector.
Turn the ignition switch to ACC.
Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.
| *a | Component with harness connected
(Map Light Assembly) |
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V6-3 (MCO+) - V6-4 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,2,3,4 |
||
| V6-5 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-2 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V6-3 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-5 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V6)Location & Routingewd_type=routing;type=c,c;code=H80,V6 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5 |
||
| H80-25 (SNS2) - V6-5 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the H85 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,H85)Location & Routingewd_type=routing;type=c,c;code=H80,H85 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=21,22,24 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=16,32 |
||
| H80-21 (MIN+) - H85-16 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - H85-32 (MCO-) | Always | Below 1 Ω |
| H80-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telematics transceiver connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V6)Location & Routingewd_type=routing;type=c,c;code=H85,V6 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=5,6,7,23 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=2,3,4 |
||
| H85-5 (MCVD) - V6-2 (MACC) | Always | Below 1 Ω |
| H85-6 (MCI+) - V6-3 (MCO+) | Always | Below 1 Ω |
| H85-7 (MCI-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H85-5 (MCVD) - Body ground | Always | 10 kΩ or higher |
| H85-6 (MCI+) - Body ground | Always | 10 kΩ or higher |
| H85-7 (MCI-) - Body ground | Always | 10 kΩ or higher |
| H85-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telematics transceiver connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=24,22 |
||
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H85 telematics transceiver connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=5 |
||
| H85-5 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=7,23 |
||
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| H85-23 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly with the connector(s) still connected.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.
| *a | Component with harness connected
(Map Light Assembly) |
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V6-3 (MCO+) - V6-4 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
Connect an oscilloscope to terminal H85-16 (MCO+) and H85-32 (MCO-).
Turn the ignition switch to ON.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.
| *a | Component with harness connected
(Telematics Transceiver) |
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | H85-16 (MCO+) - H85-32 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V6)Location & Routingewd_type=routing;type=c;code=V6 Click Connector(V6)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V6;pinno=5,2,3,4 |
||
| V6-5 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-2 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V6-3 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-5 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V7)Location & Routingewd_type=routing;type=c,c;code=H80,V7 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25,23,21,22,24 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,16,15,14 |
||
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-23 (MACC) - V7-16 (MACC) | Always | Below 1 Ω |
| H80-21 (MIN+) - V7-15 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-23 (MACC) or V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| H80-21 (MIN+) or V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=23 |
||
| H80-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=24,22 |
||
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly) |
Connect an oscilloscope to terminals 15 (MCO+) and 14 (MCO-) of the V7 map light assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V7-15 (MCO+) - V7-14 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,16,15,14 |
||
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-16 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V7-15 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,V7)Location & Routingewd_type=routing;type=c,c;code=H80,V7 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=25 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13 |
||
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) or V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the H85 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80,H85)Location & Routingewd_type=routing;type=c,c;code=H80,H85 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=21,22,24 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=16,32 |
||
| H80-21 (MIN+) - H85-16 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - H85-32 (MCO-) | Always | Below 1 Ω |
| H80-21 (MIN+) or H85-16 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or H85-32 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telematics transceiver connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,V7)Location & Routingewd_type=routing;type=c,c;code=H85,V7 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=5,6,7,23 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=16,15,14 |
||
| H85-5 (MCVD) - V7-16 (MACC) | Always | Below 1 Ω |
| H85-6 (MCI+) - V7-15 (MCO+) | Always | Below 1 Ω |
| H85-7 (MCI-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H85-5 (MCVD) or V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| H85-6 (MCI+) or V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H85-7 (MCI-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H85-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telematics transceiver connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H80)Location & Routingewd_type=routing;type=c;code=H80 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=24,22 |
||
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H85 telematics transceiver connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=5 |
||
| H85-5 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85)Location & Routingewd_type=routing;type=c;code=H85 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=7,23 |
||
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| H85-23 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
| *a | Component with harness connected
(Map Light Assembly) |
Turn the ignition switch to ACC.
Connect an oscilloscope to terminals 15 (MCO+) and 14 (MCO-) of the V7 map light assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V7-15 (MCO+) - V7-14 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telematics Transceiver) |
Remove the telematics transceiver with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
Connect an oscilloscope to terminal H85-16 (MCO+) and H85-32 (MCO-).
Turn the ignition switch to ACC.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | H85-16 (MCO+) - H85-32 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Ignition switch ACC 2.
Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(V7)Location & Routingewd_type=routing;type=c;code=V7 Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assemblyewd_type=component;type=c;code=V7;pinno=13,16,15,14 |
||
| V7-13 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V7-16 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V7-15 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V7-14 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG