Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0484174 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) D

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  DTC CHECK / CLEAR  


START DIAGNOSTIC MODE


HINT:
·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

·

Make sure that the system does not have an active connection to an Android Auto or Apple CarPlay device in order to prevent voice recognition from being activated.

·

If the system cannot enter diagnostic mode, inspect all AVC-LAN communication components and repair or replace the malfunctioning parts.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type)>AVC-LAN Circuit



a.

Turn the ignition switch to ON.


b.
E463232C01
0.354,1.792 0.844,2.052 true 0.365,0.406 0.781,0.104 true 0.052,0.031 0.365,0.229 0.313,0.198 10 false *a 0.844,0.01 1.156,0.208 0.313,0.198 10 false *b 0.885,1.979 1.198,2.177 0.313,0.198 10 false *c
*a Example
*b HOME Switch
*c Function Switch


While pressing and holding the function switch, press the HOME switch 3 times.



SYSTEM OVERVIEW


a.
E463234E01
0.698,0.625 0.542,0.146 true 1.76,0.625 1.99,0.167 true 2.646,0.594 2.875,0.135 true 1.875,2.021 1.563,1.813 true 0.375,0.021 0.688,0.219 0.313,0.198 10 false *a 2,0.042 2.313,0.24 0.313,0.198 10 false *b 2.896,0.031 3.208,0.229 0.313,0.198 10 false *c 1.906,1.958 2.219,2.156 0.313,0.198 10 false *d

System overview screen description

Screen Description
Display Content
*a: Speaker Test Pressing "Speaker Test: Start" will begin playing beep sounds from each speaker, and the test pattern will repeat until "Speaker Test: Stop" is pressed.
*b: Camera Test If a rear television camera is detected, pressing "Camera Test: Start" will display the video feed from the rear television camera even if the shift lever is not in R.
*c: Identification Mark Toyota part number and related identification mark are shown in this area.
*d: Status Indicators Displays the status of each system.
·

Green: Functioning normally, no abnormality

·

Gray: Item not functional or function cannot be confirmed, no abnormality

·

Red: Malfunction



Status Indicators List
Item Green Status Gray Status Red Status

*1: Only shown if applicable

*2: Only shown if no stereo component amplifier assembly

Rear view camera Rear television camera assembly detected Rear television camera assembly not detected
·

Previously detected, but disconnected

·

Short to ground

·

Short to VCC


External amplifier* AVC-LAN communication functional -
·

AVC-LAN communication not functional (no periodical messages)

·

Part number not matching configured parameter


Speakers* No faults detected during ACC Fault detection information not available (e.g. fault list cleared during current ACC cycle)
·

Short circuit detected (GND, VCC)

·

Detection at runtime

·

Open circuit, speaker wires short to each other (detection once only on startup)


Microphone Connected (SNS signal to GND) - SNS signal OPEN
GPS antenna GPS signal from at least 1 satellite received No faults, but no GPS signal received
·

Short to GND/VCC

·

Open


DAB antenna No fault detected -
·

Short to GND/VCC

·

Open


FM antenna Reception above threshold No faults, but reception below threshold Short to GND
CAN communication
·

No bus error condition

·

Predefined set of periodical messages received

·

Error threshold for message not received is 5 periods per message


IG OFF
·

No communication detected (list of predefined messages)

·

Error state detected on bus


MM-SUB-BUS communication
·

No bus off condition, predefined set of periodical messages received

·

Error threshold for message not received is 5 periods per message


-
·

Bus off condition detected

·

No communication detected


DCM600 Telephone transceiver assembly connected to the network (telephone transceiver assembly indicates primary APN connected)
·

Telephone transceiver assembly connected by USB but no network traffic (telephone transceiver assembly indicates primary APN not connected)

·

Initial state during connection


·

Telephone transceiver assembly is physically not connected / abnormal connection (short/open)

·

Pairing unsuccessful (handshake)


USB USB device connected No faults, but no device connected Short detected



FAULTS


a.
E463235E01
2.646,0.531 2.813,0.125 true 2.292,0.521 2.104,0.125 true 0.25,1.49 0.521,1.115 true 1.927,0.021 2.24,0.219 0.313,0.198 10 false *a 2.823,0.031 3.135,0.229 0.313,0.198 10 false *b 0.063,1.396 0.375,1.594 0.313,0.198 10 false *c

Faults screen description

Screen Description
Item Content
*a: Refresh Refresh the fault list.
*b: Clear Removes all the faults from the list.
*c: Fault list
·

List of faults occurring in the system. See below table for list of possible faults.

·

A fault can be active (currently being detected) or passive (was detected in the past, but not active anymore).

·

The number of occurrences is also shown.



Fault List
Fault Name Description Troubleshooting
Display has overheated High temperature detected in display area. System will turn off. Once it is back to normal temperature system will be turned on automatically. Replace radio and display receiver assembly if it was not operated in a high temperature environment where an overheating would be likely to occur.
Head Unit has overheated High temperature detected in chassis area. System will turn off. Once it is back to normal temperature head unit will be turned on automatically. Replace radio and display receiver assembly if it was not operated in a high temperature environment where an overheating would be likely to occur.
Amplifier has overheated High temperature detected in internal amplifier area. System will turn off. Once it is back to normal temperature head unit will be turned on automatically. Replace radio and display receiver assembly if it was not operated in a high temperature environment where an overheating would be likely to occur.
Battery Voltage High Auxiliary battery voltage above 16.5 V is detected. If normal voltage is not detected within 3 seconds then head unit will be turned off. Check power supply (auxiliary battery voltage). If supplied voltage is confirmed to be in range, replace radio and display receiver assembly.
Battery Voltage Low Auxiliary battery voltage below 8 V is detected. If normal voltage is not detected within 3 seconds then head unit will be turned off. Check power supply (auxiliary battery voltage). If supplied voltage is confirmed to be in range, replace radio and display receiver assembly.
Front/rear/left/right speaker's ground is shorted Speaker wire is shorted to vehicle GND (applies to internal amplifier). Check speaker wiring.
Front/rear/left/right speaker's VCC is shorted Speaker wire is shorted to vehicle battery (applies to internal amplifier). Check speaker wiring.
Front/rear/left/right speaker is not connected Speaker wire is not connected (applies to internal amplifier). Check speaker wiring.
Front/rear/left/right speaker's wires is shorted Speaker wires are shorted to each other (applies to internal amplifier). Check speaker wiring.
There is a malfunction in the Gyro Internal error detected in gyroscope component. Replace radio and display receiver assembly.
SWC button is stuck System is detecting continuous input from steering pad switch assembly.
·

Check that all steering pad switch assembly buttons are functioning and none of them are physically stuck.

·

Check steering pad switch assembly wire connection.


Face plate button is stuck System is detecting continuous input from radio and display assembly panel switch button. Check that all radio and display assembly panel switch buttons are functioning and none of them are physically stuck.
There is a malfunction in BT Internal error detected in Bluetooth component. Replace radio and display receiver assembly.
External Mic is disconnected System is detecting that external microphone is not connected based on SNS signal input. Check telephone microphone assembly wiring.
There is a malfunction in the USB Electrical fault detected on USB connector. Check for shorts of USB power line, USB device and USB connector.
Camera's VCC is shorted Rear television camera assembly power supply (V+) is shorted to vehicle battery. Check rear television camera assembly and wiring.
Camera's ground is shorted Rear television camera assembly power supply (V+) is shorted to vehicle ground. Check rear television camera assembly and wiring.
Signal lost from Camera Rear television camera assembly signal is lost. Check rear television camera assembly and wiring.
Tuner's ground is shorted FM antenna signal is shorted to vehicle ground. Check FM antenna and wiring.
EEP ROM not initialisation failed EEP memory content is corrupted or has not been programmed correctly. Replace radio and display receiver assembly.
Diranna initialisation failed System has detected internal error in radio tuner component. Replace radio and display receiver assembly.
Watchdog reset There is a communication malfunction between 2 components in the system (IOC and SOC). Replace radio and display receiver assembly.
GPS hardware has failed System is detecting error with GPS/GNSS component. Replace radio and display receiver assembly.
GPS ground is shorted GPS/GNSS antenna shorted to vehicle ground. Check GPS antenna connection.
GPS circuit is open GPS/GNSS antenna circuit open (disconnected). Check GPS antenna connection.
GPS VCC is shorted GPS/GNSS antenna shorted to vehicle battery. Check GPS antenna connection.
DAB circuit is open DAB antenna circuit open (disconnected). Check DAB antenna connection.
DAB ground is shorted DAB antenna shorted to vehicle ground. Check DAB antenna connection.
DAB VCC is shorted DAB antenna shorted to vehicle battery. Check DAB antenna connection.
External Amplifier open Problem detected with AVC-LAN communication with stereo component amplifier assembly. Check stereo component amplifier assembly data connection or stereo component amplifier assembly wiring.
DCM ground is shorted An issue with power supply of telephone transceiver assembly is detected. Check telephone transceiver assembly connector and wiring for electrical faults.
DCM network interface error Network sharing interface with telephone transceiver assembly could not be established.
·

Ensure telephone transceiver assembly is connected.

·

Confirm telephone transceiver assembly function or replace telephone transceiver assembly.


DCM connection error USB connection to telephone transceiver assembly cannot be confirmed. Confirm wiring between radio and display receiver assembly and telephone transceiver assembly.
DCM service protocol error Telephone transceiver assembly communication protocol is returning an error.
·

Perform battery cycle

·

Confirm telephone transceiver assembly function or replace telephone transceiver assembly.


Meter Global CAN faulty Messages from combination meter assembly not received by radio and display receiver assembly. Check CAN interface connection of radio and display receiver assembly and combination meter assembly
BDB Global CAN faulty Messages from main body ECU (multiplex network body ECU) not received by radio and display receiver assembly. Check CAN interface connection of radio and display receiver assembly and main body ECU (multiplex network body ECU)
ENG Global CAN faulty Messages from ECM not received by radio and display receiver assembly. Check CAN interface connection of radio and display receiver assembly and ECM
Meter Local CAN faulty Messages from combination meter assembly not received on MM-SUB-Bus. Check local CAN connection to radio and display receiver assembly and combination meter assembly.
CAN bus is off CAN bus off condition detected on MM-SUB-Bus. Check local CAN connection to radio and display receiver assembly and combination meter assembly.
Amplifier number mismatch System detects incorrect amplifier is connected Replace stereo component amplifier assembly.



LOGGING


a.
E463244E01
0.615,0.552 0.469,0.146 true 1.313,0.844 2.083,0.188 true 1.313,1.031 3.104,0.177 true 2.198,2.01 1.313,1.219 true 0.333,2.042 0.74,1.469 true 0.302,0.031 0.615,0.229 0.313,0.198 10 false *a 2.094,0.052 2.406,0.25 0.313,0.198 10 false *b 3.104,0.052 3.417,0.25 0.313,0.198 10 false *c 2.208,1.958 2.521,2.156 0.313,0.198 10 false *d 0.177,1.979 0.49,2.177 0.313,0.198 10 false *e

Logging screen description

Screen Description
Item Content
*a: Fast Logging These features are for development purposes only. These items are disabled for production systems.
*b: USB Live Logging
*c: HCI Debug
*d Copy to USB
*e: Activate Screenshot If a USB drive (FAT32 formatted) is inserted into USB port, this function can be enabled. When enabled, press function switch to store a screenshot of the device onto the USB drive.



SYSTEM PARAMETERS


a.
E463237E01
0.948,0.521 1.26,0.115 true 1.281,0.021 1.594,0.219 0.313,0.198 10 false *a

System Parameters screen description

Screen Description
Item Content
*a: System Parameters Displays the output of various parameters.

System Parameters List
Item Content
ACC signal ACC signal input state
IG signal IG signal input state (CAN-bus and/or analog input)
Parking brake signal PKB signal input state (CAN-bus and/or analog input)
Reverse gear signal REV signal input state (CAN-bus and/or analog input)
ILL signal ILL signal input state (analog input)
ADIM signal ADIM signal input state (CAN-bus input)
Vehicle speed Vehicle speed signal input state (CAN-bus or analog input)
System time Current GPS time (UTC timezone)
Tuner frequency Currently selected frequency for FM/DAB
Tuner station name Currently selected station name for FM/DAB
Tuner signal strength Signal strength for currently playing FM/DAB station
Bluetooth signal strength Signal strength for currently connected Bluetooth device
GPS number of satellites Number of satellites currently received by GNSS receiver
GPS fix status Current status for GNSS location (no fix, 2D fix, 3D fix)
GPS latitude Current latitude coordinate calculated by GNSS receiver
GPS longitude Current longitude coordinate calculated by GNSS receiver
Accelerometer Output values from internal accelerometer
Gyroscope Output values from internal gyroscope
CNR average Average signal-to-noise ratio for GNSS receiver
Battery voltage Current voltage level measured from auxiliary battery
Temperature CPU Current temperature measured at CPU
Temperature amplifier Current temperature measured at internal amplifier
Temperature display Current temperature measured at display



DCM


a.
E463245E01
1.271,0.542 1.635,0.125 true 2.833,0.833 3.198,0.417 true 1.323,1.792 1.76,2.042 true 1.667,0.021 1.979,0.219 0.313,0.198 10 false *a 3.188,0.26 3.406,0.458 0.219,0.198 10 false *b 1.792,1.948 2.104,2.146 0.313,0.198 10 false *c

DCM screen description

Screen Description
Item Content
*a: AvMap Debug Server This feature is for development purposes only. This item is disabled for production systems.
*b: Refresh Press this button to update the parameter list.
*c: Parameter List Parameter list received from telephone transceiver is displayed. The received parameters can vary.



OTHER


a.
E463246E01
0.896,0.552 1.219,0.146 true 1.302,0.844 2.01,0.167 true 1.083,1.073 1.76,2.01 true 1.24,0.031 1.552,0.229 0.313,0.198 10 false *a 2,0.042 2.313,0.24 0.313,0.198 10 false *b 1.802,1.948 2.115,2.146 0.313,0.198 10 false *c

Other screen description

Screen Description
Item Content
*a: Picture Viewer When a USB drive with pictures is inserted, these pictures can be displayed from this menu. Supported picture formats: GIF/JPG
*b: Video Player When a USB drive with video files is inserted, these videos can be displayed from this menu. Supported video formats: MP4, M4V, 3GP, 3G2, Flash F4V(F4P, F4V, F4A, F4B), Nero Digital, QuickTime (MOV, QT), AVI
*c: Browser configuration This feature is for development purposes only. This item is disabled for production systems.

HINT:

The user is able to block the touchscreen, hardkeys and steering pad switch assembly using the following key combination:

1.

Tap 3 times in bottom left corner of the touchscreen

2.

Tap 3 times in top right corner of the touchscreen


The same combination will unlock the touchscreen, hardkeys and steering pad switch assembly. A pop-up will be shown (and autohide after 3s) to indicate user how to unlock the system




FINISH DIAGNOSTIC MODE


a.

Turn the ignition switch off or press the HOME switch.