Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0484174 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  Cannot Establish Wi-Fi Connection  


PROCEDURE

1.CHECK "Wi-Fi" CONNECTION SETTING
a.

Check that the following "Wi-Fi" connection setting conditions are met.

·

"Wi-Fi" connection setting is turned on

·

Communication setting is set to "Wi-Fi"



Result:
Proceed to
OK
NG



OK

2.CHECK ENVIRONMENT AND PROCEDURES

NG

PERFORM WI-FI SETTING AGAIN

2.CHECK ENVIRONMENT AND PROCEDURES
a.

Check the conditions and procedure for establishing a "Wi-Fi" connection, and perform "Wi-Fi" connection again.

HINT:
·

As there may be wave interference, disconnect other "Wi-Fi" compatible devices or "Bluetooth" compatible devices before establishing a "Wi-Fi" connection.

·

A "Wi-Fi" connection can be established manually or automatically.

·

There are 3 ways to establish a manual connection: Connecting using simple setting, connecting by searching for a "Wi-Fi" access point and inputting a password, and connecting by inputting an SSID and password.

·

Even though an automatic connection is enabled, a connection can be established only when a "Wi-Fi" access point with the same SSID and password that were used for a previous connection exists.

·

It may not be possible to establish a "Wi-Fi" connection in a region other than the region where the vehicle was purchased.




Result:
Result Proceed to
"Wi-Fi" connection can be established. A
"Wi-Fi" connection cannot be established. B



A

END

B

3.CHECK PORTABLE DEVICE
3.CHECK PORTABLE DEVICE
a.

Bring a portable device to be used to establish a "Wi-Fi" connection into the cabin and perform "Wi-Fi" connection again near the in-vehicle device.

HINT:
·

Considering the radio wave environment around the vehicle, move the vehicle and establish a "Wi-Fi" connection.

·

Depending on the portable device, operation by the customer (Internet sharing, tethering settings, etc.) may be required each time a "Wi-Fi" connection is established.




Result:
Result Proceed to
"Wi-Fi" connection can be established. A
"Wi-Fi" connection cannot be established. B



A

END

B

4.CHECK CONDITION OF "Wi-Fi" ACCESS POINT
4.CHECK CONDITION OF "Wi-Fi" ACCESS POINT
a.

Check the condition of portable device.

HINT:
·

The head unit may not be able to connect to the access point due to the condition of the portable device (e.g., the power may not be turned on, tethering may be turned off, or the SSID (name of access point) may not be sent).

·

When the power of the portable device is turned off, tethering may be turned off.




Result:
Result Proceed to
The power is off or tethering is turned off (access point). A
Other than above. B



A

RESTART ACCESS POINT

B

5.CHECK IF "Wi-Fi" ACCESS POINT IS DISCOVERED ON MANUAL SEARCH
5.CHECK IF "Wi-Fi" ACCESS POINT IS DISCOVERED ON MANUAL SEARCH
a.

Check if the "Wi-Fi" access point is discovered on a manual search.


Result:
Result Proceed to
There are no search results and SSID is not sent (access point). A
The device is detected via a network search. B



A

FOLLOW SETTING METHOD FOR EACH PORTABLE DEVICE IN ORDER TO SET ACCESS POINT TO BROADCAST SSID

B

6.PERFORM "Wi-Fi" CONNECTION IN OTHER PLACE
6.PERFORM "Wi-Fi" CONNECTION IN OTHER PLACE
a.

Change the location to another place and perform "Wi-Fi" connection.

NOTICE:

Bring the portable device close to the display of the system device.



Result:
Result Proceed to
"Wi-Fi" connection can be established. A
Function cannot be stabilized. B
Even though setting is performed, "Wi-Fi" connection cannot be established. C



A

END

B

FUNCTION THAT USES "Wi-Fi" IS MALFUNCTIONING

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY