Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0484174 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E463257E01
1.479,1.885 2.698,2.323 1.219,0.438 10 false Stereo Component Amplifier Assembly 1.49,1.719 3.458,1.958 1.969,0.24 10 false H137 4.469,1.708 4.833,1.938 0.365,0.229 10 false H79 4.469,1.875 5.656,2.333 1.188,0.458 10 false Radio and Display Receiver Assembly 4.635,1.156 5.229,1.354 0.594,0.198 10 false MUT1 4.375,1.052 4.646,1.292 0.271,0.24 10 false 25 2.615,1.042 2.885,1.281 0.271,0.24 10 false 1 2.115,1.135 2.604,1.344 0.49,0.208 10 false MUTE

CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type)>PRECAUTION


PROCEDURE

1.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E447055C01
1.479,0.792 1.938,1.073 0.458,0.281 2.396,1.885 2.865,2.385 true 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.531,0.833 2.094,1.052 0.563,0.219 10 false H137 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Remove the stereo component amplifier assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H137)Location & Routing

Click Connector(H137)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H137-1 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Changing modes
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the H137 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H79,H137)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(H137)Instrument Panel>Instrument Panel Wire / Speaker Wire>Stereo Component Amplifier Assembly

H79-25 (MUT1) - H137-1 (MUTE) Always Below 1 Ω
H79-25 (MUT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H79)Location & Routing

Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

H79-25 (MUT1) - Body ground Ignition switch ACC, audio system is playing 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY