Home › Vehicle Interior › POWER OUTLETS (INT) › WIRELESS CHARGING SYSTEM › from 2021.07
RM3700E _58 Vehicle Interior _093029 POWER OUTLETS (INT) _0484176 WIRELESS CHARGING SYSTEM J

POWER OUTLETS (INT)  WIRELESS CHARGING SYSTEM  Wireless Charger Power Source Circuit  


DESCRIPTION

This is the power source circuit for the mobile wireless charger cradle assembly.

WIRING DIAGRAM

E409569E05
0.406,0.74 1.813,0.927 1.406,0.188 10 false from Auxiliary Battery 0.74,1.406 1.802,1.635 1.063,0.229 10 false from ACC Relay 2.51,0.948 3.646,1.125 1.135,0.177 10 false ECU-DCC NO. 2 2.708,1.604 3.458,1.823 0.75,0.219 10 false ECU-ACC 4.198,0.615 4.354,0.813 0.156,0.198 10 false 6 4.198,1.292 4.354,1.49 0.156,0.198 10 false 5 4.208,2.427 4.365,2.625 0.156,0.198 10 false 1 4.188,2.021 4.344,2.219 0.156,0.198 10 false 8 4.438,0.74 4.75,0.938 0.313,0.198 10 false B+ 4.438,1.292 4.896,1.49 0.458,0.198 10 false ACC 4.458,2.552 5.073,2.75 0.615,0.198 10 false PGND 4.438,2.125 5.052,2.323 0.615,0.198 10 false SDET* 4.177,3.063 4.635,3.26 0.458,0.198 10 false H86 4.177,3.26 6.854,3.5 2.677,0.24 10 false Mobile Wireless Charger Cradle Assembly 5.823,1.417 6.135,1.615 0.313,0.198 10 false IC 0.219,3.281 2.156,3.5 1.938,0.219 10 false *: w/o Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B




A

2.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY POWER SOURCE)

B

3.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY POWER SOURCE)
a.

Disconnect the H86 mobile wireless charger cradle assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H86)Location & Routing

Click Connector(H86)Instrument Panel>Instrument Panel Wire / Speaker Wire>Mobile Wireless Charger Cradle Assembly

H86-1 (PGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H86)Location & Routing

Click Connector(H86)Instrument Panel>Instrument Panel Wire / Speaker Wire>Mobile Wireless Charger Cradle Assembly

H86-6 (B+) - Body ground Ignition switch off 11 to 14 V
H86-5 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY POWER SOURCE)
a.

Disconnect the H86 mobile wireless charger cradle assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H86)Location & Routing

Click Connector(H86)Instrument Panel>Instrument Panel Wire / Speaker Wire>Mobile Wireless Charger Cradle Assembly

H86-1 (PGND) - Body ground Always Below 1 Ω
H86-8 (SDET) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(H86)Location & Routing

Click Connector(H86)Instrument Panel>Instrument Panel Wire / Speaker Wire>Mobile Wireless Charger Cradle Assembly

H86-6 (B+) - Body ground Ignition switch off 11 to 14 V
H86-5 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR