FREEZE FRAME DATA/INFORMATION
Using the GTS, check the vehicle condition (ECU, sensor) when a DTC is output.
CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED
Freeze Frame Data is stored when a DTC is output.
Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Check the Freeze Frame Data when a DTC is output.
Turn the ignition switch off.
Connect the GTS to the DLC3 and turn the ignition switch to ON.
Select a DTC to display the Freeze Frame Data.
Check the Freeze Frame Data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Value | Steering sensor | Min.: -3276.8°
Max.: 3276.7° |
Turning left: 0.0 to 3276.7
Turning right: -3276.8 to 0.0° |
- |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | - |
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC(TRAC)/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Normal mode (TRC(TRAC) ON/VSC ON): Normal mode TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRAC off mode Not
defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode / Pressure hold mode / Pressure release mode / EPB lock mode | Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed | Vehicle speed (estimated vehicle speed used for various controls) | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle acceleration/deceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Downhill Assist Control SW | Downhill assist control switch | OFF / ON | OFF: Downhill assist control switch OFF
ON: Downhill assist control switch ON |
- |
| Stop Light SW | Stop light switch assembly (STP terminal input) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake status | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (CSW2 terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) status (STP terminal input) | OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
- |
| TRC(TRAC) Control | TRC(TRAC) control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC(TRAC) engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC(TRAC) brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | OFF / ON | OFF: Not operating
ON: Operating |
- |
| Regenerative Cooperation | Regenerative cooperation | OFF / ON | OFF: Not operating
ON: Operating |
- |
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF
ON: VSC OFF switch ON |
- |
| Reservoir Warning SW | Brake fluid level warning switch | OFF / ON | OFF: Reservoir level normal
ON: Reservoir level low |
- |
| ECB Motor Relay | Motor relay operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Motor Relay2 | Motor relay 2 operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SGH) | Switching solenoid valve (SGH) | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SSA) | Switching solenoid valve (SSA) | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 off
ON: IGP_PT1 on |
- |
| IGP_PT2 | IGP_PT2 status | OFF / ON | OFF: IGP_PT2 off
ON: IGP_PT2 on |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel LH | Forward / Back | - | - |
| FR Speed Open | Front speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FL Speed Open | Front speed sensor LH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RR Speed Open | Rear speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RL Speed Open | Rear speed sensor LH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Open | Yaw rate sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Deceleration Open | Acceleration sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Steering Open | Steering sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Air Bag ECU Communication Open | Airbag sensor assembly open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Stroke Open | Brake pedal stroke sensor 1 open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Stroke2 Open | Brake pedal stroke sensor 2 open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Accumulator Open | Accumulator pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| HV Communication Open | Hybrid vehicle communication open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure Sensor Open | Reaction force pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Servo Pressure Sensor Open | Servo pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa
Max.: 24.48 MPa |
0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal Brake pedal released: 0.00 Mpa |
| Reaction Force Pressure Sensor Temperature | Reaction force pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) | - |
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor 2 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 3.6 to 4.35 V | Reading increases when brake pedal is depressed |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm
Max.: 255 mm |
Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa
Max.: 24.48 MPa |
Brake pedal released: 0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Servo Pressure Sensor Temperature | Servo pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) | Current servo pressure sensor temperature |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa
Max.: 24.48 MPa |
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Accumulator Pressure Sensor Temperature | Accumulator pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30°C (-22°F) to 100°C (212°F) | - |
| Voltage of Stroke Sensor | Voltage of brake pedal stroke sensor2 | Min.: -2.500 V
Max.: 2.490 V |
- | - |
| Voltage of Stroke Sensor2 | Voltage of brake pedal stroke sensor2 | Min.: -2.500 V
Max.: 2.490 V |
- | - |
| FR Regenerative Request | FR regenerative request torque | Min.: 0 Nm
Max.: 1048560 Nm |
- | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| FR Regenerative Operation | FR regenerative operation torque | Min.: 0 Nm
Max.: 1048560 Nm |
- | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| Brake Pedal Stroke Change Speed | Brake pedal stroke rate of change | Min.: -2560 mm/s
Max.: 2540 mm/s |
Brake pedal released or depressed and held: 0 mm/s | Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal |
| Reaction Force Oil Pressure Change Speed | Reaction force pressure rate of change | Min.: -30 MPa/s
Max.: 225 MPa/s |
- | - |
| Target Oil Pressure | Wheel target hydraulic pressure | Min.: 0.00 MPa
Max.: 20.00 Mpa |
- | Changes according to the target wheel cylinder hydraulic pressure |
| VCSK Voltage Value | VCSK voltage value | Min.: 0.000 V
Max.: 5.500 V |
4.800 to 5.200 V | - |
| SLA Solenoid Current | Switching solenoid valve (SLA) current | Min.: 0.000 A
Max.: 1.500 A |
0.000 to 1.500 A | - |
| SLR Solenoid Current | Switching solenoid valve (SLR) current | Min.: 0.000 A
Max.: 1.500 A |
0.000 to 1.500 A | - |
| SGH Solenoid Current | Switching solenoid valve (SGH) current | Min.: 0.000 A
Max.: 3.000 A |
0.00 to 1.50 A | - |
| SSA Solenoid Current | Switching solenoid valve (SSA) current | Min.: 0.000 A
Max.: 3.000 A |
0.00 to 1.50 A | - |
| IGP Voltage | IGP voltage value | 0.000 to 20.000 V | - | Changes in proportion to auxiliary battery voltage |
| IGR Voltage | IGR voltage value | 0.000 to 20.000 V | - | Changes in proportion to auxiliary battery voltage |
| VM1 Voltage | VM1 voltage value | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| VM2 Voltage | VM2 voltage value | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| BS(linear) Voltage | BS voltage value (for SLA, SLR) | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| BS(ABS) Voltage | BS voltage value (for SGH, SSA) | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| VCM1 Voltage | VCM1 voltage value | Min.: 0.000 V
Max.: 20.000 V |
6.290 to 7.640 V | - |
| VCM2 Voltage | VCM2 voltage value | Min.: 0.000 V
Max.: 20.000 V |
6.290 to 7.640 V | - |
*1: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>TEST MODE PROCEDURE
*2: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY
CLEAR FREEZE FRAME DATA AND INFORMATION
Clearing the DTCs will also clear the Freeze Frame Data.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs and Freeze Frame Data.