DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant
speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant
speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant
speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant
speed: No large fluctuations |
| FR Wheel Acceleration | Front wheel RH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
Vehicle stopped: 0.0 km/h (0 mph) | During deceleration/ acceleration: Changes continuously |
| FL Wheel Acceleration | FL Wheel Acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
Vehicle stopped: 0.0 km/h (0 mph) | During deceleration/ acceleration: Changes continuously |
| RR Wheel Acceleration | RR Wheel Acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
Vehicle stopped: 0.0 km/h (0 mph) | During deceleration/ acceleration: Changes continuously |
| RL Wheel Acceleration | RL Wheel Acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
Vehicle stopped: 0.0 km/h (0 mph) | During deceleration/ acceleration: Changes continuously |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 |
During acceleration/ deceleration: Changes in proportion with acceleration |
| Zero Point of Decele2 | Memorized zero value | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
- | - |
| Zero Point of Decele | Memorized zero value | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
- | - |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Zero Point of Yaw Rate Sensor | Memorized zero point value of yaw rate sensor 1 | Min.: -128°/s
Max.: 127°/s |
After completing zero point calibration: 0° | - |
| Zero Point of Yaw Rate Sensor2 | Memorized zero point value of yaw rate sensor 2 | Min.: -128°/s
Max.: 127°/s |
After completing zero point calibration: 0° | - |
| Steering Angle Value | Steering sensor | Min.: -3276.8°
Max.: 3276.7° |
- | During steering operation: Changes in proportion with steering wheel rotation |
| Zero Point of Steering Angle | Memorized zero point value of steering sensor | Min.: -3276.8°
Max.: 3276.7° |
- | - |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Vehicle Speed | Vehicle speed (estimated vehicle speed used for various controls) | Min.: 0.0 km/h (0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC(TRAC)/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) | Normal mode (TRC(TRAC) ON/VSC ON): Normal mode TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRAC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode | - |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode / Pressure hold mode / Pressure release mode / EPB lock mode | Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 Mpa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed Grade | Vehicle acceleration/deceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Downhill Assist Control SW | Downhill assist control switch | OFF / ON | OFF: Downhill assist control switch OFF
ON: Downhill assist control switch ON |
- |
| Stop Light SW | Stop light switch assembly (STP terminal input) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Parking Brake SW | Parking brake status | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (CSW2 terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) status (STP terminal input) | OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
- |
| TRC(TRAC) Control | TRC(TRAC) control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC(TRAC) engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC(TRAC) brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| BA Ctrl Status | BA Ctrl Status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| Regenerative Cooperation | Regenerative cooperation | OFF / ON | OFF: Not operating
ON: Operating |
- |
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (CSW terminal input) | OFF / ON | OFF: VSC OFF switch OFF
ON: VSC OFF switch ON |
- |
| Reservoir Warning SW | Brake fluid level warning switch | OFF / ON | OFF: Reservoir level normal
ON: Reservoir level low |
- |
| ECB Motor Relay | Brake fluid level warning switch | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Motor Relay2 | Motor relay 2 operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SGH) | Switching solenoid valve (SGH) | OFF / ON | OFF: Solenoid off
ON: Solenoid on |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SSA) | Switching solenoid valve (SSA) | OFF / ON | OFF: Solenoid off
ON: Solenoid on |
ECB: Electronically Controlled Brake System |
| MTT | Pump motor operation status | OFF / ON | OFF: Pump motor off
ON: Pump motor on |
- |
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 off
ON: IGP_PT1 on |
- |
| IGP_PT2 | IGP_PT2 status | OFF / ON | OFF: IGP_PT2 off
ON: IGP_PT2 on |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel LH | Forward / Back | - | - |
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa
Max.: 24.48 MPa |
0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal Brake pedal released: 0.00 Mpa |
| Reaction Force Pressure Sensor Temperature | Reaction force pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
Current reaction force pressure sensor temperature | - |
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor 2 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 3.65 to 4.35 V | Reading decreases when brake pedal is depressed |
| Quantity of Brake Pedal Stroke | Brake pedal stroke amount | Min.: 0 mm
Max.: 255 mm |
Brake pedal released: 0 mm | Reading increases when brake pedal is depressed |
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa
Max.: 24.48 MPa |
Brake pedal released: 0.00 to 21.60 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Servo Pressure Sensor Temperature | Servo pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
-30 to 100°C | Current servo pressure sensor temperature |
| Accumulator Pressure | Accumulator pressure output value | Min.: 0.00 MPa
Max.: 24.48 MPa |
15.00 to 21.00 MPa (Pressure stable and pump motor stopped) | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
| Accumulator Pressure Sensor Temperature | Accumulator pressure sensor temperature | Min.: -80°C (-112°F)
Max.: 175°C (347°F) |
Current accumulator pressure sensor temperature | - |
| Voltage of Stroke Sensor | Voltage of brake pedal stroke sensor1 | Min.: -2.500 V
Max.: 2.490 V |
- | - |
| Voltage of Stroke Sensor2 | Voltage of brake pedal stroke sensor2 | Min.: -2.500 V
Max.: 2.490 V |
- | - |
| FR Regenerative Request | FR regenerative request torque | Min.: 0 Nm
Max.: 1048560 Nm |
- | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| FR Regenerative Operation | FR regenerative operation torque | Min.: 0 Nm
Max.: 1048560 Nm |
- | Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.) |
| Brake Pedal Stroke Change Speed | Brake pedal stroke rate of change | Min.: -2560 mm/s
Max.: 2540 mm/s |
Brake pedal released or depressed and held: 0 mm/s | Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal |
| Reaction Force Oil Pressure Change Speed | Reaction force pressure rate of change | Min.: -30 MPa/s
Max.: 225 MPa/s |
- | - |
| Target Oil Pressure | Wheel target hydraulic pressure | Min.: 0.00 MPa
Max.: 20.00 Mpa |
- | Changes according to the target wheel cylinder hydraulic pressure |
| VCSK Voltage Value | VCSK voltage value | Min.: 0.00 MPa
Max.: 5.500 V |
4.800 to 5.200 V | - |
| SLA Solenoid Current | Linear solenoid addition valve (SLA) current | Min.: 0.000 A
Max.: 1.500 A |
Brake pedal released: 0.000 A | - |
| SLR Solenoid Current | Linear solenoid reduction valve (SLR) current | Min.: 0.000 A
Max.: 1.500 A |
Brake pedal released: 0.000 A | - |
| SGH Solenoid Current | Switching solenoid valve (SGH) current | Min.: 0.000 A
Max.: 3.000 A |
0.000 to 1.500 A | - |
| SSA Solenoid Current | Switching solenoid valve (SSA) current | Min.: 0.000 A
Max.: 3.000 A |
0.000 to 1.500 A | - |
| STPO | Stop light control relay (Stop light switch assembly) status(STPO terminal output) | OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off (Stop light off)
ON: Stop light control relay (Stop light switch assembly) on (Stop light on) |
|
| ABS Solenoid (SRLR) | Rear pressure reduction solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SRLH) | Rear pressure holding solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SRRR) | Rear pressure reduction solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SRRH) | Rear pressure holding solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SFLR) | Front pressure reduction solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SFLH) | Front pressure holding solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SFRR) | Front pressure reduction solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SFRH) | Front pressure holding solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Motor Relay | Motor relay | OFF / ON | OFF: Motor relay off
ON: Motor relay on |
- |
| Solenoid Relay | Solenoid relay | OFF / ON | OFF: Solenoid relay off
ON: Solenoid relay on |
- |
| ECB Main Relay | Motor relay operation request | OFF / ON | OFF: Relay off
ON: Relay on |
ECB: Electronically Controlled Brake System |
| IGP Voltage | IGP voltage value | 0.000 to 20.000 V | - | Changes in proportion to auxiliary battery voltage |
| IGR Voltage | IGR voltage value | 0.000 to 20.000 V | - | Changes in proportion to auxiliary battery voltage |
| VM1 Voltage | VM1 voltage value | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| VM2 Voltage | VM2 voltage value | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| BS(linear) Voltage | BS voltage value (for SLA, SLR) | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| BS(ABS) Voltage | BS voltage value (for SGH, SSA) | Min.: 0.000 V
Max.: 20.000 V |
- | Changes in proportion to auxiliary battery voltage |
| VCM1 Voltage | VCM1 voltage value | Min.: 0.000 V
Max.: 10.000 V |
6.290 to 7.640 V | - |
| VCM2 Voltage | VCM2 voltage value | Min.: 0.000 V
Max.: 10.000 V |
6.290 to 7.640 V | - |
*1: for performing Dealer Mode (Signal Check):
*2: for entering Dealer Mode (Calibration):
CHECK FOR INTERMITTENT PROBLEMS
A momentary interruption (open circuit) in the connectors and/or wire harnesses between the sensors and ECUs can be detected using the Data List function of the GTS.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Follow the directions on the GTS to display the Data List and select areas where momentary interruptions should be monitored.
A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Speed Open | Front speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FL Speed Open | Front speed sensor LH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RR Speed Open | Rear speed sensor RH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RL Speed Open | Rear speed sensor LH open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Open | Yaw rate sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Deceleration Open | Acceleration sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Steering Open | Steering sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor voltage open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Air Bag ECU Communication Open | Airbag sensor assembly open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Stroke Open | Brake pedal stroke sensor 1 open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Stroke2 Open | Brake pedal stroke sensor 2 open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Accumulator Open | Accumulator pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| HV Communication Open | Hybrid vehicle communication open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Reaction Force Pressure Sensor Open | Reaction force pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
| Servo Pressure Sensor Open | Servo pressure sensor open detection | Normal / Under intermittent | Normal: Normal
Under intermittent: Momentary interruption |
- |
Push the line graph button to display the line graph.
Check for intermittent shorts, etc.
Normal is displayed.
If "Under intermittent" remains displayed on the GTS, measure the resistance between the skid control ECU and the each sensor, hybrid vehicle control ECU or airbag sensor assembly.
While observing the screen, gently jiggle the connectors or wire harnesses between the ECUs and sensors, or between ECUs.
Normal is displayed.
If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.
If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.
DATA LIST (STEERING ANGLE SENSOR)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the GTS to read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Steering Angle Signal Information | Steering angle value
(Rotation to the left side is positive) |
Min.: -3070.5 deg
Max.: 3070.5 deg |
Turning left: 0.0 to 3070.5 deg
Turning right: -3070.5 to 0.0 deg |
During steering operation: Changes in proportion with steering wheel rotation |
| Sensor Malfunction Factor (Current) | Sensor malfunction factor (current) | Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck | - | - |
| Sensor Malfunction Factor (Past) | Sensor malfunction factor (past) | Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck | - | - |
| Total Distance Traveled (When Sensor Malfunction occurred) | Total distance traveled (when sensor malfunction occurred) | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit (When Sensor Malfunction occurred) | Total distance traveled unit (when sensor malfunction occurred) | km / mile | - | - |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Restrict Condition | Diagnostic Note |
|---|---|---|---|---|
| EBS Relay | Emergency brake signal operation | Relay Start | Vehicle condition: Vehicle stopped
|
This item is displayed on the GTS but is not used |
| ABS Solenoid | Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR) |
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P or N ·
Apply the parking brake
|
Check that the GTS display for the solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR or SFRH) changes to ON/OFF during Solenoid Start (Activate) |
| VSC Solenoid | Master cylinder cut solenoid (SMF (SM1), SMR (SM2)) | Solenoid Start (Activate)
Solenoid SMF / SMR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P or N ·
Apply the parking brake
|
Check that the GTS display for the solenoid (SM1 or SM2) changes to ON/OFF during Solenoid Start (Activate) |
| ECB Solenoid | Linear solenoid addition valve (SLR, SLA)
Switching solenoid valve (SSA, SGH) |
Solenoid Start (Activate)
Solenoid SLR / SLA / SSA / SGH |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P or N ·
Apply the parking brake
|
Check that the GTS display for the solenoid (SLR, SLA, SSA, SGH) changes to ON/OFF during Solenoid Start (Activate) |
| Motor Relay | ABS motor relay | OFF / ON | Vehicle condition: Vehicle stopped
|
Operating sound of motor can be heard |
| Solenoid Relay | Solenoid Relay | OFF / ON | Vehicle condition: Vehicle stopped
|
Perform the Active Test and check that the voltage displayed for the solenoid power supply voltage Data List item changes. |
| Stop Lamp Relay | Stop light control relay (Stop light switch assembly) | OFF / ON | Vehicle condition: Vehicle stopped
|
With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON |
| ECB Main Relay | Main relay | OFF / ON | Vehicle condition: Vehicle stopped
|
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SLR) | Linear solenoid reduction valve (SLR) | Solenoid Start (Activate)
Solenoid SLR (It is possible to set the current) |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P ·
Apply the parking brake |
ECB: Electronically Controlled Brake System |
| ECB Solenoid (SLA) | Linear solenoid addition valve (SLA) | Solenoid Start (Activate)
Solenoid SLA (It is possible to set the current) |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P ·
Apply the parking brake |
ECB: Electronically Controlled Brake System |