The skid control ECU (brake actuator assembly) receives signals from the ECM, steering sensor and airbag sensor assembly via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| U007488 | Control Module Communication Bus "B" Off Bus Off | Any of the following is detected:
·
A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. ·
When the +BS terminal voltage is between 9.5 and 17.4 V, a delay in receiving data from the yaw rate and acceleration sensor (airbag sensor assembly) and steering sensor continues for 1 second or more. ·
When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds: -
A delay in receiving data from the yaw rate and acceleration sensor (airbag sensor assembly) and steering sensor occurs once or more within 5 seconds. |
CAN communication system | Brake/EPB | B |
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 15 km/h (9 mph), data cannot be received from the ECM for 2 seconds or more. | ·
CAN communication system ·
ECM ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | B |
| U010187 | Lost Communication with TCM Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 15 km/h (9 mph), data cannot be received from the TCM (ECM) for 2 seconds or more. | ·
CAN communication system ·
TCM ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | B |
| U012587 | Lost Communication with Multi-axis Acceleration Sensor Module Missing Message | Either of the following is detected:
·
When the +BS terminal voltage is between 9.5 and 17.4 V, data from the acceleration sensor cannot be received for 1 second or more. ·
When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds: -
Data from the acceleration sensor cannot be received once or more within 5 seconds. |
·
CAN communication system ·
Acceleration sensor (airbag sensor assembly) ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | B |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Either of the following is detected:
·
When the +BS terminal voltage is between 9.5 and 17.4 V, data from the steering sensor cannot be received for 1 second or more. ·
When the +BS terminal voltage is between 9.5 and 17.4 V, the following occurs 10 times in succession within 60 seconds: -
Data from the steering sensor cannot be received once or more within 5 seconds |
·
CAN communication system ·
Steering sensor ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | B |
| U015187 | Lost Communication with Restraints Control Module Missing Message | When the +BS terminal voltage is between 9.5 and 17.4 V and the vehicle speed exceeds 7 km/h (4 mph), data cannot be received from the airbag sensor assembly for 5 seconds or more. | ·
CAN communication system ·
Airbag sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake/EPB | B |
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Check the DTCs that are output.
| Result | Proceed to |
|---|---|
| U007488, U010087, U010187, U012587, U012687 or U015187 is output | A |
| DTCs are not output | B |
| None of the above conditions are met | C |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
C