Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  TERMINALS OF ECU  


TERMINALS OF ECU


C339682C22
0.198,0.146 0.51,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU (brake actuator assembly) ground
2 - (Not used)
3 - (Not used)
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
8 - (Not used)
9 (CSW) VSC OFF switch (combination switch assembly)
10 - (Not used)
11 (STP) Stop light switch assembly input
12 - (Not used)
13 - (Not used)
14 (+BS) Solenoid relay power supply
15 - (Not used)
16 - (Not used)
17 - (Not used)
18 (SP1) Speed signal output for speedometer
19 (RR-) Rear wheel speed RH (-) signal input
20 (RR+) Rear wheel speed RH (+) power supply output
21 (FL-) Front wheel speed LH (-) signal input
22 (FL+) Front wheel speed LH (+) power supply output
23 - (Not used)
24 - (Not used)
25 - (Not used)
26 - (Not used)
27 (CANH) CAN communication line H
28 - (Not used)
29 - (Not used)
30 (GND2) Pump motor ground
31 - (Not used)
32 (STPO) Stop light switch assembly output
33 - (Not used)
34 - (Not used)
35 (BH) Brake hold switch (electric parking brake switch assembly) input
36 - (Not used)
37 (STP2) Stop light switch assembly input
38 - (Not used)
39 - (Not used)
40 - (Not used)
41 - (Not used)
42 - (Not used)
43 (CANL) CAN communication line L
44 - (Not used)
45 (IGR) ECU power supply input
46 (BM) Motor relay power supply


TERMINAL INSPECTION


a.

Disconnect the A94 connector and measure the voltage or resistance on the wire harness side.

C343082C11
3.333,0.448 3.771,0.75 0.438,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.427,0.521 3.885,0.719 0.458,0.198 10 false A94
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A94-1 (GND1) - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω
A94-9 (CSW) - Body ground VSC OFF switch (combination switch assembly) input VSC OFF switch (combination switch assembly) pressed and held → released Below 1 Ω → 10 kΩ or higher
A94-11 (STP) - Body ground Stop light switch assembly input Stop light switch assembly on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A94-14 (+BS) - Body ground Solenoid relay power supply Always 11 to 14 V
A94-18 (SP1) - Body ground Speed signal output for speedometer Ignition switch ON 11 to 14 V
A94-30 (GND2) - Body ground Pump motor ground Always Below 1 Ω
A94-32 (STPO) - Body ground Stop light switch assembly output Ignition switch ON 11 to 14 V
A94-35 (BH) - Body ground Brake hold switch (electric parking brake switch assembly) input Brake hold switch (electric parking brake switch assembly) pressed and held → released Below 1 Ω → 10 kΩ or higher
A94-37 (STP2) - Body ground Stop light switch assembly input Brake pedal depressed → released 8 to 14 V → Below 1.5 V
A94-45 (IGR) - Body ground ECU power supply input Ignition switch ON 11 to 14 V
A94-46 (BM) - Body ground Motor relay power supply Always 11 to 14 V