DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the GTS to read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FR Wheel Acceleration | Front wheel RH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| FL Wheel Acceleration | Front wheel LH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| RR Wheel Acceleration | Rear wheel RH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| RL Wheel Acceleration | Rear wheel LH acceleration | Min.: -200.840 m/s2
Max.: 199.271 m/s2 |
- | ·
Displays a positive value during deceleration/acceleration ·
During deceleration/acceleration: Changes continuously |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa
Max.: 23.99 MPa |
Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| Zero Point of M/C | Memorized zero value | Min.: -12.5 MPa
Max.: 12.4 MPa |
- | - |
| Master Cylinder Sensor Temperature | Master cylinder pressure sensor temperature | Min.: -80°C
Max.: 175°C |
Displays temperature master cylinder pressure sensor | - |
| M/C Sensor Grade | Master cylinder pressure sensor change (value detected by ECU) | Min.: -30 MPa/s
Max.: 225 MPa/s |
Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Zero Point of Decele2 | Memorized zero value (lateral G) | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
- | - |
| Zero Point of Decele | Memorized zero value (forward and rearward G) | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
- | - |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Zero Point of Yaw Rate Sensor | Memorized zero value | Min.: -128°/s
Max.: 127°/s |
After completing zero point calibration: 0° | - |
| Steering Angle Value | Steering sensor | Min.: -3276.8°
Max.: 3276.7° |
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0° |
- |
| Zero Point of Steering Angle | Memorized zero value | Min.: -3276.8°
Max.: 3276.7° |
- | - |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Real Engine Torque | Powertrain drive torque | Min.: -1024.000 Nm
Max.: 1023.000 Nm |
- | - |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) |
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode Not defined: Not defined VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode /
Pressure hold mode / Pressure release mode / EPB lock mode |
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated) Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed Grade | Vehicle acceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Vehicle Stop Time from IG ON | Time vehicle stopped after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Travel Distance from IG ON | Driving time after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Stop Light SW | Stop light switch assembly
(STP terminal input) |
OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake switch | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Reverse Position Switch | Reverse position switch | OFF / ON | OFF: Reverse position switch OFF
ON: Reverse position switch ON |
- |
| Brake Hold Switch | Brake hold switch (electric parking brake switch assembly) (BH terminal input) | OFF / ON | OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON |
|
| Stop Light Relay | Stop light control relay (stop light switch assembly) status
(STP terminal input) |
OFF / ON | OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
|
| TRC(TRAC) Control | TRC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| Stop Light Relay State for ECU Control | Semiconductor PWR integration ECU status (STPO terminal output) (value detected by ECU) | OFF / ON | OFF: Semiconductor PWR integration ECU not operating
ON: Semiconductor PWR integration ECU operating |
- |
| Solenoid State for ECU Control | ABS solenoid relay status (for ECU control) | OFF / ON | OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating |
- |
| Motor State for ECU Control | ABS motor relay status (for ECU control) | OFF / ON | OFF: ABS motor relay not operating
ON: ABS motor relay operating |
- |
| Operation History of IG OFF while Vehicle is moving | History of ignition switch turned off when vehicle is in motion | OFF / ON | OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (combination switch assembly) (CSW terminal input) | OFF / ON | OFF: VSC OFF switch (combination switch assembly) OFF
ON: VSC OFF switch (combination switch assembly) ON |
|
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 off
ON: IGP_PT1 on |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel LH | Forward / Back | - | - |
| FR Speed Open | Front speed sensor RH open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| FL Speed Open | Front speed sensor RH open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| RR Speed Open | Rear speed sensor RH open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| RL Speed Open | Rear speed sensor LH open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| EFI Communication Open | ECM communication open detection | Under intermittent / Normal | Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected |
- |
| Yaw Rate Open | Yaw rate sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Deceleration Open | Acceleration sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Steering Open | Steering sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Master Cylinder Open | Master cylinder pressure sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| M/C Pressure Sensor Noise | Master cylinder pressure sensor noise detection | Under intermittent / Normal | Under intermittent: Noise detected
Normal: Noise not detected |
- |
| Yaw Rate Sensor Voltage Open | Yaw rate sensor voltage open detection | Under intermittent / Normal | Under intermittent / Normal
Normal: Momentary interruption not detected |
- |
| EFI Communication Invalid | ECM communication invalid detection | Under intermittent / Normal | Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected |
- |
| Master Cylinder Pressure Sensor Power Supply Open | Master cylinder pressure sensor power supply voltage status | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Solenoid Power Supply Open | Solenoid power supply voltage status | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Motor Power Supply Open | Motor power supply voltage status | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| Stop Switch Open | Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| A/C ECU Communication Open | Air conditioning amplifier assembly communication open detection | Normal / Under intermittent | Normal: Momentary interruption not detected
Under intermittent: Momentary interruption detected |
- |
| Air Bag ECU Communication Open | Airbag sensor assembly open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
- |
| ABS Solenoid (SRLR) | Rear pressure reduction solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SRLH) | Rear pressure holding solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SRRR) | Rear pressure reduction solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SRRH) | Rear pressure holding solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SFLR) | Front pressure reduction solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SFLH) | Front pressure holding solenoid LH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| ABS Solenoid (SFRR) | Front pressure reduction solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure reduction) |
|
| ABS Solenoid (SFRH) | Front pressure holding solenoid RH status | OFF / ON | OFF: Not operating
ON: Operating (pressure holding) |
|
| TRC(TRAC)/VSC Solenoid (SM2) | Master cylinder cut solenoid (Brake Pressure Control Solenoid "B") status | OFF / ON | OFF: Not operating
ON: Operating (pressure regulation) |
|
| TRC(TRAC)/VSC Solenoid (SM1) | Master cylinder cut solenoid (Brake Pressure Control Solenoid "A") status | OFF / ON | OFF: Not operating
ON: Operating (pressure regulation) |
|
| ABS Motor Relay | Motor relay | OFF / ON | OFF: Motor relay off
ON: Motor relay on |
- |
| Solenoid Relay | Solenoid relay | OFF / ON | OFF: Solenoid relay off
ON: Solenoid relay on |
- |
| STPO | Semiconductor PWR integration ECU (STPO terminal output) | OFF / ON | OFF: Semiconductor PWR integration ECU off (Stop light off)
ON: Semiconductor PWR integration ECU on (Stop light on) |
|
| IGR Voltage | IGR terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage |
| +BS Voltage | +BS terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| +BM Voltage | BM terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
*1: for entering inspection mode:
*2: for performing Dealer Mode (Signal Check):
*3: for entering Dealer Mode (Calibration):
DATA LIST (STEERING ANGLE SENSOR)
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the GTS to read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Steering Angle Signal Information | Steering angle value
(Rotation to the left side is positive) |
Min.: -3070.5 deg
Max.: 3070.5 deg |
Turning left: 0.0 to 3070.5 deg
Turning right: -3070.5 to 0.0 deg |
During steering operation: Changes in proportion with steering wheel rotation |
| Sensor Malfunction Factor (Current) | Sensor malfunction factor (current) | Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck | - | - |
| Sensor Malfunction Factor (Past) | Sensor malfunction factor (past) | Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck | - | - |
| Total Distance Traveled (When Sensor Malfunction occurred) | Total distance traveled (when sensor malfunction occurred) | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit (When Sensor Malfunction occurred) | Total distance traveled unit (when sensor malfunction occurred) | km / mile | - | - |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Operate the GTS to perform the Active Test.
| Tester Display | Measurement Item | Control Range | Restrict Condition | Diagnostic Note |
|---|---|---|---|---|
| EBS Relay | - | - | - | Not applicable to this vehicle |
| ABS Solenoid | Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR) |
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P ·
Apply the parking brake
|
Refer to on-vehicle inspection for the brake actuator* |
| VSC Solenoid | Master cylinder cut solenoid (SMF (SM1), SMR (SM2)) | Solenoid Start (Activate)
Solenoid SMF / SMR |
Vehicle condition:
·
Vehicle stopped ·
Shift lever is in P ·
Apply the parking brake
|
Check that the GTS display for the solenoid (SM1 or SM2) changes to ON/OFF during Solenoid Start (Activate) |
| Motor Relay | ABS motor relay | OFF / ON | Vehicle condition: Vehicle stopped
|
Refer to on-vehicle inspection for the brake actuator* |
| Solenoid Relay | Solenoid relay | OFF / ON | Vehicle condition: Vehicle stopped
|
Perform the Active Test and check that the voltage displayed for the solenoid power supply voltage Data List item changes. |
| Stop Lamp Relay | Stop light switch assembly (STPO terminal output) | OFF / ON | Vehicle condition: Vehicle stopped
|
Check that the stop light switch assembly (STPO terminal output) turns ON when the brake pedal is released, the stop lights illuminate, and the "stop light relay" and "STPO" Data List items switch to ON. |
*:Refer to on-vehicle inspection for the brake actuator