Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is pressed while the ignition switch is ON.

Conditions required for operation standby:

(a)

The driver door is closed.

(b)

The driver seat belt is fastened.

(c)

The system is normal.



HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system



WIRING DIAGRAM

C467245E01
5.344,4.083 6.885,4.479 1.542,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 2.927,4.333 4.677,4.563 1.75,0.229 10 false : CAN Communication Line 0.094,4.042 2,4.302 1.906,0.26 10 false Combination Meter Assembly 3.396,3.229 5.094,3.854 1.698,0.625 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 5.354,3.927 5.813,4.125 0.458,0.198 10 false A94 3.406,3.073 3.865,3.271 0.458,0.198 10 false H140 0.094,3.896 0.552,4.094 0.458,0.198 10 false H6 0.906,0.927 1.521,1.125 0.615,0.198 10 false CANH 0.885,1.75 1.5,1.948 0.615,0.198 10 false CANL 5.365,0.896 5.979,1.094 0.615,0.198 10 false CANH 5.365,1.708 5.979,1.906 0.615,0.198 10 false CANL 1.385,1.573 1.698,1.771 0.313,0.198 10 false 25 1.375,0.771 1.688,0.969 0.313,0.198 10 false 9 5.083,0.75 5.396,0.948 0.313,0.198 10 false 27 5.094,1.563 5.406,1.76 0.313,0.198 10 false 43 5.094,2.615 5.406,2.813 0.313,0.198 10 false 35 4.698,2.625 5.01,2.823 0.313,0.198 10 false 10 3.573,2.635 3.885,2.833 0.313,0.198 10 false 12 3.823,2.635 3.979,2.833 0.156,0.198 10 false E 4.438,2.635 4.667,2.833 0.229,0.198 10 false +B 5.344,2.615 5.698,2.854 0.354,0.24 10 false BH 6.5,2.75 6.813,2.948 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver door is closed.

2.

The driver seat belt is fastened.

3.

The system is normal.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system




Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (BRAKE HOLD READY)
2.READ VALUE USING GTS (BRAKE HOLD READY)
a.

Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
Chassis > Brake/EPB > Data List
Tester Display
Brake Hold Ready
50003 435 164
Standard:
Brake Hold Switch (Electric Parking Brake Switch Assembly) Operation Mode Condition Display Brake Hold Standby Indicator Light
Not pressed Not in stand-by mode Does not come on
Pressing the brake hold switch (electric parking brake switch assembly) Stand-by mode Come on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display are normal C



A

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

B

C

3.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Inspect the brake hold switch (electric parking brake switch assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE HOLD SWITCH>INSPECTION

OK:

The brake hold switch (electric parking brake switch assembly) operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H140,A94)Location & Routing

Click Connector(H140)Instrument Panel>Instrument Panel Wire / Speaker Wire>Electric Parking Brake Switch Assembly

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

H140-10 (+B) - A94-35 (BH) Always Below 1 Ω
H140-10 (+B) or A94-35 (BH) - Body ground Always 10 kΩ or higher
H140-12 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR