| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| C060E19 | Left Electric Parking Brake Actuator Circuit Current Above Threshold | When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly LH 3 times. | ·
Parking brake actuator assembly LH ·
No. 2 parking brake wire assembly ·
Wire harness and connector ·
Skid control ECU (brake actuator assembly) |
DTC stored | Brake/EPB | A | An electric parking brake system malfunction is displayed on the multi-information display. |
The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned ON.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Pre-procedure1
Disconnect the uO2 and u3 No. 2 parking brake wire assembly connectors.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Procedure3
Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 2 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly LH) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO2,u3)Location & Routingewd_type=routing;type=w,c;code=uO2,u3 Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO2;pinno=1,2 Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LHewd_type=component;type=c;code=u3;pinno=2,1 |
||
| uO2-1 - u3-2 (+) | Always | Below 1 Ω |
| uO2-1 or u3-2 (+) - Body ground and other terminals | Always | 10 kΩ or higher |
| uO2-2 - u3-1 (-) | Always | Below 1 Ω |
| uO2-2 or u3-1 (-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Disconnect the u3 parking brake actuator assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A94,u3)Location & Routingewd_type=routing;type=c,c;code=A94,u3 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=3,2 Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LHewd_type=component;type=c;code=u3;pinno=2,1 |
||
| A94-3 (MRL+) - u3-2 (+) | Always | Below 1 Ω |
| A94-3 (MRL+) or u3-2 (+) - Body ground | Always | 10 kΩ or higher |
| A94-2 (MRL-) - u3-1 (-) | Always | Below 1 Ω |
| A94-2 (MRL-) or u3-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMC Made 2WD)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Turn the ignition switch off.
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the u3 parking brake actuator assembly LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u3)Location & Routingewd_type=routing;type=c;code=u3 Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LHewd_type=component;type=c;code=u3;pinno=2,1 |
||
| u3-2 (+) - u3-1 (-) | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the uO2 No. 2 parking brake wire assembly connector.
Procedure1
| *a | Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO2)Location & Routingewd_type=routing;type=w;code=uO2 Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO2;pinno=1,2 |
||
| uO2-1 - uO2-2 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the uO2 No. 2 parking brake wire assembly connector.
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector | *b | (to Skid Control ECU (Brake Actuator Assembly)) |
| *c | (to No. 2 Parking Brake Wire Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO2,A94)Location & Routingewd_type=routing;type=w,c;code=uO2,A94 Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO2;pinno=1,2 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=3,2 |
||
| uO2-1 or A94-3 (MRL+) - Body ground | Always | Below 1 V |
| uO2-2 or A94-2 (MRL-) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG