Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0484415 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMC Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMC Made)  C061011  Right Electric Parking Brake Actuator Control Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C061011 Right Electric Parking Brake Actuator Control Circuit Short to Ground
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator RH internal circuit (short to GND).

·

Detection Time:

Approximately 0.015 to 0.195 seconds (depending on each malfunction)


·

Parking brake actuator assembly RH

·

No. 1 parking brake wire assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C402632E76
1.313,0.677 1.927,0.875 0.615,0.198 10 false MRR+ 1.344,1.281 1.958,1.479 0.615,0.198 10 false MRR- 3.604,1.292 4.063,1.49 0.458,0.198 10 false uO1 3.604,0.698 4.063,0.896 0.458,0.198 10 false uO1 5.031,1.094 5.208,1.365 0.177,0.271 10 false 1 3.677,1.083 3.854,1.354 0.177,0.271 10 false 2 3.677,0.49 3.854,0.76 0.177,0.271 10 false 1 5.042,0.5 5.219,0.771 0.177,0.271 10 false 2 4.99,1.292 5.302,1.49 0.313,0.198 10 false u1 5,0.698 5.313,0.896 0.313,0.198 10 false u1 5.281,1.802 6.75,2.198 1.469,0.396 10 false Parking Brake Actuator Assembly RH 3.708,1.802 4.979,2.354 1.271,0.552 10 false No. 1 Parking Brake Wire Assembly 0.583,1.833 1.083,2.083 0.5,0.25 10 false A94 0.583,2 2.167,2.417 1.583,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 1.813,0.583 2.125,0.781 0.313,0.198 10 false 13 1.813,1.177 2.125,1.375 0.313,0.198 10 false 12 5.344,0.698 6.01,0.948 0.667,0.25 10 false + 5.354,1.292 5.969,1.458 0.615,0.167 10 false -

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the uO1 and u1 No. 1 parking brake wire assembly connectors.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

C427097C34
1.813,0.24 2.229,0.49 0.417,0.25 5.01,0.281 5.427,0.531 0.417,0.25 4.333,2.167 4.969,1.667 true 5.938,2.198 5.427,1.677 true 1.885,0.281 2.344,0.479 0.458,0.198 10 false uO1 5.125,0.313 5.583,0.51 0.458,0.198 10 false u1 6,2.156 6.417,2.406 0.417,0.25 10 false + 4.229,2.125 4.688,2.323 0.458,0.198 10 false - 1.948,2.365 2.406,2.573 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 5.146,2.25 5.604,2.448 0.458,0.198 10 false *c
*a Front view of No. 1 Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly RH) - -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,u1)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

uO1-1 or u1-2 (+) - Body ground and other terminals Always 10 kΩ or higher
uO1-2 or u1-1 (-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Make sure the No. 1 parking brake wire assembly is securely installed.


c.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the u1 parking brake actuator assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A94,u1)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(u1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly RH

A94-13 (MRR+) or u1-2 (+) - Body ground Always 10 kΩ or higher
A94-12 (MRR-) or u1-1 (-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH