Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › from 2021.07
RM3700E _58 Vehicle Interior _093747 DOOR LOCK _0445091 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69030A 1.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

Pre-procedure 1

a.
B566000C02
0.625,2.438 1.125,2.688 0.5,0.25 1.281,3.75 1.417,4.167 true 1.083,3.792 1.083,4.167 true 0.729,3.802 0.667,4.167 true 0.188,2.625 0.5,2.781 0.313,0.156 10 false *a 0.542,0.375 0.854,0.531 0.313,0.156 10 false *b 1.063,0.198 1.375,0.354 0.313,0.156 10 false *c 1.635,0.406 1.948,0.563 0.313,0.156 10 false *d 0.625,4.219 0.938,4.375 0.313,0.156 10 false E 1.083,4.229 1.396,4.385 0.313,0.156 10 false L 1.438,4.229 1.75,4.385 0.313,0.156 10 false UL 0.76,2.49 1.073,2.74 0.313,0.25 10 false K11
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Neutral
*d Lock


Measure the resistance according to the value(s) in the table below.


Procedure 1

b.

Check the resistance of the lock and unlock switch.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K11)Location & Routing

Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RH

K11-6(L) - K11-8(E) Lock Below 1 Ω
K11-6(L) - K11-8(E) Neutral 10 kΩ or higher
K11-5(UL) - K11-8(E) Unlock Below 1 Ω
K11-5(UL) - K11-8(E) Neutral 10 kΩ or higher



c.

If the result is not as specified, replace the front door lock assembly RH.


Post-procedure 1

d.

None


Pre-procedure 2

e.
B566001C04
1.479,2.958 1.979,3.208 0.5,0.25 1.333,4.5 1.594,4.25 true 2.177,4.49 1.844,4.24 true 0.688,3.083 1,3.24 0.313,0.156 10 false *a 2.24,2.708 2.552,2.865 0.313,0.156 10 false *b 1.292,2.688 1.604,2.844 0.313,0.156 10 false *c 2.219,4.5 2.615,4.667 0.396,0.167 10 false LSSR 1.25,4.51 1.563,4.667 0.313,0.156 10 false E 1.615,3.01 1.927,3.167 0.313,0.156 10 false K11
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 2

f.

Check the door lock motor operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(K11)Location & Routing

Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RH

K11-4(L) - Auxiliary battery positive (+)
K11-1(UL) - Auxiliary battery negative (-)
Lock
K11-1(UL) - Auxiliary battery positive (+)
K11-4(L) - Auxiliary battery negative (-)
Unlock



g.

If the result is not as specified, replace the front door lock assembly RH.


Post-procedure 2

h.

None


Pre-procedure 3

i.
B566001C05
1.479,2.958 1.979,3.208 0.5,0.25 1.281,3.896 0.917,3.75 true 2.177,3.885 2.5,3.75 true 0.688,3.083 1,3.24 0.313,0.156 10 false *a 2.24,2.708 2.552,2.865 0.313,0.156 10 false *b 1.292,2.688 1.604,2.844 0.313,0.156 10 false *c 0.771,3.667 1.083,3.823 0.313,0.156 10 false L 2.583,3.667 2.896,3.823 0.313,0.156 10 false UL 1.615,3.01 1.927,3.167 0.313,0.156 10 false K11
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Lock
*c Unlock


Measure the resistance according to the value(s) in the table below.


Procedure 3

j.

Check the operation of the door unlock detection switch.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K11)Location & Routing

Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RH

K11-7(LSSR) - K11-8(E) Lock 10 kΩ or higher
K11-7(LSSR) - K11-8(E) Unlock Below 1 Ω



k.

If the result is not as specified, replace the front door lock assembly RH.


Post-procedure 3

l.

None


Hide 69030A 2.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

Pre-procedure 1

a.
B228539C05
1.5,3 2,3.25 0.5,0.25 2.188,4.115 2.531,4.115 true 1.667,4.156 1.531,4.417 true 2.031,4.156 2.167,4.417 true 0.104,0.906 0.271,1.052 0.167,0.146 10 false *b 0.5,0.573 0.667,0.719 0.167,0.146 10 false *c 1.229,0.76 1.385,0.906 0.156,0.146 10 false *d 0.917,3.01 1.073,3.167 0.156,0.156 10 false *a 1.458,4.438 1.573,4.583 0.115,0.146 10 false E 2.146,4.438 2.24,4.583 0.094,0.146 10 false L 2.594,4.01 2.885,4.167 0.292,0.156 10 false UL 1.615,3.042 1.99,3.281 0.375,0.24 10 false K11
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Unlock
*c Neutral
*d Lock


Measure the resistance according to the value(s) in the table below.


Procedure 1

b.

Check the door lock motor operation.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K11)Location & Routing

Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RH

K11-6(L) - K11-8(E) Lock Below 1 Ω
K11-6(L) - K11-8(E) Neutral 10 kΩ or higher
K11-5(UL) - K11-8(E) Unlock Below 1 Ω
K11-5(UL) - K11-8(E) Neutral 10 kΩ or higher



c.

If the result is not as specified, replace the front door lock assembly RH.


Post-procedure 1

d.

None


Pre-procedure 2

e.
B228537C04
1.479,2.99 1.979,3.24 0.5,0.25 1.344,3.792 0.979,3.646 true 2.188,3.802 2.51,3.667 true 1.917,3.781 2.594,3.344 true 1.615,3.771 1.021,3.385 true 0.625,3.01 0.938,3.167 0.313,0.156 10 false *a 1.615,2.76 1.927,2.917 0.313,0.156 10 false *b 0.854,2.438 1.167,2.594 0.313,0.156 10 false *c 0.771,3.573 1.083,3.729 0.313,0.156 10 false DL 2.563,3.583 2.875,3.74 0.313,0.156 10 false UL 1.604,3.031 1.917,3.188 0.313,0.156 10 false K11 2.646,3.25 2.958,3.406 0.313,0.156 10 false L 0.615,3.302 1.104,3.469 0.49,0.167 10 false UNDL
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 2

f.

Check the door lock motor operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(K11)Location & Routing

Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RH

K11-2(L) - Auxiliary battery positive (+)
K11-1(UL) - Auxiliary battery negative (-)
Lock
K11-1(UL) - Auxiliary battery positive (+)
K11-2(L) - Auxiliary battery negative (-)
Unlock
K11-4(DL) - Auxiliary battery positive (+)
K11-3(UNDL) - Auxiliary battery negative (-)
Sets
K11-3(UNDL) - Auxiliary battery positive (+)
K11-4(DL) - Auxiliary battery negative (-)
Unsets



g.

If the result is not as specified, replace the front door lock assembly RH.


Post-procedure 2

h.

None


Pre-procedure 3

i.
B228537C05
1.552,3.063 1.969,3.313 0.417,0.25 1.521,4.156 1.26,4.427 true 1.875,4.146 2.135,4.417 true 1.708,4.146 1.708,4.406 true 1.354,4.125 0.969,4.125 true 0.677,3.188 0.896,3.396 0.219,0.208 10 false *a 1.615,2.76 1.865,2.99 0.25,0.229 10 false *b 0.927,2.417 1.177,2.656 0.25,0.24 10 false *c 1.667,4.438 1.781,4.583 0.115,0.146 10 false E 2,4.438 2.406,4.583 0.406,0.146 10 false LSSR 0.99,4.438 1.375,4.583 0.385,0.146 10 false DLSR 0.813,4.031 0.927,4.177 0.115,0.146 10 false E 1.635,3.094 1.979,3.281 0.344,0.188 10 false K11
*a Component without harness connected
(Front Door Lock Assembly RH)
*b Lock
*c Unlock


Measure the resistance according to the value(s) in the table below.


Procedure 3

j.

Check the operation of the door unlock detection switch.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K11)Location & Routing

Click Connector(K11)Body>Front Door Wire RH / Television Camera Wire>Front Door Lock with Motor Assembly RH

K11-7(LSSR) - K11-8(E) Lock 10 kΩ or higher
K11-7(LSSR) - K11-8(E) Unlock Below 1 Ω
K11-9(DSSR) - K11-10(E) Sets 10 kΩ or higher
K11-9(DSSR) - K11-10(E) Unsets Below 1 Ω



k.

If the result is not as specified, replace the front door lock assembly RH.


Post-procedure 3

l.

None


Hide 69040A 3.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

Pre-procedure 1

a.
B566003C02
1.521,2.99 1.958,3.229 0.438,0.24 1.313,3.885 0.917,3.667 true 2.167,3.906 2.5,3.667 true 1.458,4.458 1.594,4.24 true 1.99,4.458 1.823,4.24 true 0.833,3.073 1.146,3.229 0.313,0.156 10 false *a 1.167,2.708 1.479,2.865 0.313,0.156 10 false *b 2.104,2.719 2.417,2.875 0.313,0.156 10 false *c 0.802,3.604 0.958,3.802 0.156,0.198 10 false L 2.573,3.583 2.875,3.781 0.302,0.198 10 false UL 1.146,4.5 1.635,4.667 0.49,0.167 10 false LSSR 2.083,4.51 2.229,4.667 0.146,0.156 10 false E 1.625,3.042 1.938,3.198 0.313,0.156 10 false L11
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 1

b.

Check the door lock motor operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(L11)Location & Routing

Click Connector(L11)Body>Front Door Wire LH / Television Camera Wire>Front Door Lock with Motor Assembly LH

L11-4(L) - Auxiliary battery positive (+)
L11-1(UL) - Auxiliary battery negative (-)
Lock
L11-1(UL) - Auxiliary battery positive (+)
L11-4(L) - Auxiliary battery negative (-)
Unlock



c.

If the result is not as specified, replace the front door lock assembly LH.


Post-procedure 1

d.

None


Pre-procedure 2

e.

Measure the resistance according to the value(s) in the table below.


Procedure 2

f.

Check the operation of the door unlock detection switch. (w/ Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L11)Location & Routing

Click Connector(L11)Body>Front Door Wire LH / Television Camera Wire>Front Door Lock with Motor Assembly LH

L11-7(E) - L11-8(LSSR) Lock 10 kΩ or higher
L11-7(E) - L11-8(LSSR) Unlock Below 1 Ω



g.

If the result is not as specified, replace the front door lock assembly LH.


Post-procedure 2

h.

None


Hide 69040A 4.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

Pre-procedure 1

a.
B228536C07
1.5,3 2,3.25 0.5,0.25 0.969,3.854 1.344,3.854 true 2.229,3.854 2.594,3.854 true 1.594,3.771 1.281,3.115 true 1.958,3.771 2.271,3.115 true 0.708,3.135 0.896,3.313 0.188,0.177 10 false *a 2.354,2.458 2.521,2.604 0.167,0.146 10 false *c 1.51,2.781 1.667,2.927 0.156,0.146 10 false *b 1.021,3.031 1.323,3.229 0.302,0.198 10 false UL 0.833,3.771 0.927,3.927 0.094,0.156 10 false L 2.646,3.781 3.052,3.927 0.406,0.146 10 false UNDL 2.323,3.021 2.531,3.167 0.208,0.146 10 false DL 1.625,3.042 1.958,3.208 0.333,0.167 10 false L11
*a Component without harness connected
(Front Door Lock Assembly LH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 1

b.

Check the door lock motor operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(L11)Location & Routing

Click Connector(L11)Body>Front Door Wire LH / Television Camera Wire>Front Door Lock with Motor Assembly LH

L11-4(L) - Auxiliary battery positive (+)
L11-3(UL) - Auxiliary battery negative (-)
Lock
L11-3(UL) - Auxiliary battery positive (+)
L11-4(L) - Auxiliary battery negative (-)
Unlock
L11-2(DL) - Auxiliary battery positive (+)
L11-1(UNDL) - Auxiliary battery negative (-)
Sets
L11-1(UNDL) - Auxiliary battery positive (+)
L11-2(DL) - Auxiliary battery negative (-)
Unsets



c.

If the result is not as specified, replace the front door lock assembly LH.


Post-procedure 1

d.

None


Pre-procedure 2

e.
B228536C08
1.5,3 2,3.25 0.5,0.25 1.333,4.427 1.677,4.125 true 1.823,4.448 1.865,4.135 true 2,4.135 2.208,4.469 true 2.208,4.125 2.573,4.125 true 0.854,3.229 1.042,3.406 0.188,0.177 10 false *a 2.354,2.458 2.521,2.604 0.167,0.146 10 false *c 1.521,2.781 1.729,2.958 0.208,0.177 10 false *b 1.167,4.458 1.667,4.667 0.5,0.208 10 false LSSR 2.25,4.406 2.75,4.594 0.5,0.188 10 false DSSR 1.771,4.458 1.958,4.635 0.188,0.177 10 false E 2.625,4.042 2.813,4.219 0.188,0.177 10 false E 1.625,3.021 2.125,3.229 0.5,0.208 10 false L11

Measure the resistance according to the value(s) in the table below.


Procedure 2

f.

Check the operation of the door unlock detection switch.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(L11)Location & Routing

Click Connector(L11)Body>Front Door Wire LH / Television Camera Wire>Front Door Lock with Motor Assembly LH

L11-7(E) - L11-8(LSSR) Lock 10 kΩ or higher
L11-7(E) - L11-8(LSSR) Unlock Below 1 Ω
L11-6(DSSR) - L11-5(E) Sets 10 kΩ or higher
L11-6(DSSR) - L11-5(E) Unsets Below 1 Ω



g.

If the result is not as specified, replace the front door lock assembly LH.


Post-procedure 2

h.

None