Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2021.07
RM3700E _58 Vehicle Interior _093747 DOOR LOCK _0445092 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69050A 1.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

Pre-procedure 1

a.
B566016C04
1.583,3.094 1.938,3.271 0.354,0.177 2.021,4.24 2.25,4.51 true 1.448,4.24 1.208,4.51 true 2.177,3.958 2.469,3.958 true 0.958,3.948 1.25,3.948 true 2.302,4.51 2.729,4.667 0.427,0.156 10 false LSSR 1.104,4.51 1.26,4.667 0.156,0.156 10 false E 2.021,2.896 2.344,3.073 0.323,0.177 10 false *b 1.563,2.885 1.969,3.083 0.406,0.198 10 false *c 0.583,3.229 0.833,3.427 0.25,0.198 10 false *a 0.833,3.885 1.115,4.083 0.281,0.198 10 false L 2.542,3.896 2.823,4.094 0.281,0.198 10 false UL 1.667,3.104 1.896,3.25 0.229,0.146 10 false M1
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 1

b.

Check the door lock motor operation.

Specified Condition:
Tester Connection Specified Condition

Click Location & Routing(M1)Location & Routing

Click Connector(M1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

M1-4(L) - Auxiliary battery positive (+)
M1-1(UL) - Auxiliary battery negative (-)
Lock
M1-1(UL) - Auxiliary battery positive (+)
M1-4(L) - Auxiliary battery negative (-)
Unlock



c.

If the result is not as specified, replace the rear door lock assembly RH.


Post-procedure 1

d.

None


Pre-procedure 2

e.

Measure the resistance according to the value(s) in the table below.


Procedure 2

f.

Check the operation of the door unlock detection switch. (w/ Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M1)Location & Routing

Click Connector(M1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

M1-6(LSSR) - M1-9(E) Lock 10 kΩ or higher
M1-6(LSSR) - M1-9(E) Unlock Below 1 Ω



g.

If the result is not as specified, replace the rear door lock assembly RH.


Post-procedure 2

h.

None


Hide 69050A 2.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

Pre-procedure 1

a.
B228544C05
1.583,3.083 1.906,3.271 0.323,0.188 2.219,3.844 2.51,3.844 true 1.021,3.844 1.313,3.844 true 1.594,3.781 0.948,3.281 true 1.948,3.781 2.573,3.302 true 2.323,2.625 2.646,2.802 0.323,0.177 10 false *b 1.458,2.625 1.865,2.823 0.406,0.198 10 false *c 0.396,2.927 0.865,3.177 0.469,0.25 10 false *a 0.885,3.76 1.167,3.958 0.281,0.198 10 false L 2.563,3.75 3.021,3.969 0.458,0.219 10 false UNDL 1.656,3.094 1.875,3.271 0.219,0.177 10 false M1 2.625,3.208 2.906,3.406 0.281,0.198 10 false DL 0.708,3.198 1.167,3.417 0.458,0.219 10 false UL
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 1

b.

Check the door lock motor operation.

OK:
Tester Connection Specified Condition

Click Location & Routing(M1)Location & Routing

Click Connector(M1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

M1-4 (L) - Auxiliary battery positive (+)
M1-3 (UL) - Auxiliary battery negative (-)
Lock
M1-3 (UL) - Auxiliary battery positive (+)
M1-4 (L) - Auxiliary battery negative (-)
Unlock
M1-2 (DL) - Auxiliary battery positive (+)
M1-1 (UNDL) - Auxiliary battery negative (-)
Sets
M1-1 (UNDL) - Auxiliary battery positive (+)
M1-2 (DL) - Auxiliary battery negative (-)
Unsets



c.

If the result is not as specified, replace the rear door lock assembly RH.


Post-procedure 1

d.

None


Pre-procedure 2

e.
B228544C10
1.521,3 2.021,3.25 0.5,0.25 0.958,4.125 1.354,4.125 true 2.208,4.115 2.604,4.115 true 2.167,4.448 2.01,4.146 true 1.406,4.438 1.531,4.156 true 0.802,3.115 0.969,3.271 0.167,0.156 10 false *a 2.396,2.656 2.552,2.802 0.156,0.146 10 false *b 1.385,2.656 1.542,2.802 0.156,0.146 10 false *c 1.167,4.458 1.708,4.656 0.542,0.198 10 false LSSR 0.792,4.042 0.979,4.24 0.188,0.198 10 false E 2.646,4.031 3.146,4.219 0.5,0.188 10 false DLSR 2.167,4.469 2.396,4.667 0.229,0.198 10 false E 1.667,3.042 2.167,3.229 0.5,0.188 10 false M1
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Measure the resistance according to the value(s) in the table below.


Procedure 2

f.

Check the operation of the door unlock detection switch.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M1)Location & Routing

Click Connector(M1)Body>No. 1 Rear Door Wire>Rear Door Lock with Motor Assembly RH

M1-9 (LSSR) - M1-10 (E) Lock 10 kΩ or higher
M1-9 (LSSR) - M1-10 (E) Unlock Below 1 Ω
M1-5 (DLSR) - M1-6 (E) Sets 10 kΩ or higher
M1-5 (DLSR) - M1-6 (E) Unsets Below 1 Ω



g.

If the result is not as specified, replace the rear door lock assembly RH.


Post-procedure 2

h.

None


Hide 69060A 3.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

Pre-procedure 1

a.
B566018C04
1.594,3.083 1.958,3.271 0.365,0.188 2.021,4.24 2.26,4.51 true 1.448,4.24 1.229,4.51 true 2.177,3.979 2.469,3.979 true 0.99,3.958 1.281,3.958 true 2.26,4.531 3,4.667 0.74,0.135 10 false LSSR 1.135,4.51 1.302,4.667 0.167,0.156 10 false E 1.281,2.896 1.604,3.073 0.323,0.177 10 false *b 1.698,2.885 2.104,3.083 0.406,0.198 10 false *c 0.479,3.219 0.948,3.469 0.469,0.25 10 false *a 0.865,3.896 1.146,4.094 0.281,0.198 10 false L 2.531,3.917 2.813,4.115 0.281,0.198 10 false UL 1.698,3.094 1.896,3.25 0.198,0.156 10 false N1
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 1

b.

Check the door lock motor operation.

Specified Condition:
Tester Connection Specified Condition

Click Location & Routing(N1)Location & Routing

Click Connector(N1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

N1-4(L) - Auxiliary battery positive (+)
N1-1(UL) - Auxiliary battery negative (-)
Lock
N1-1(UL) - Auxiliary battery positive (+)
N1-4(L) - Auxiliary battery negative (-)
Unlock



c.

If the result is not as specified, replace the rear door lock assembly LH.


Post-procedure 1

d.

None


Pre-procedure 2

e.

Measure the resistance according to the value(s) in the table below.


Procedure 2

f.

Check the operation of the door unlock detection switch. (w/ Entry and Start System)

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N1)Location & Routing

Click Connector(N1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

N1-6(LSSR) - N1-9(E) Lock 10 kΩ or higher
N1-6(LSSR) - N1-9(E) Unlock Below 1 Ω



g.

If the result is not as specified, replace the rear door lock assembly LH.


Post-procedure 2

h.

None


Hide 69060A 4.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

Pre-procedure 1

a.
B228543C07
1.583,3.083 1.906,3.271 0.323,0.188 1.031,3.844 1.323,3.844 true 1.958,3.781 2.563,3.469 true 1.604,3.781 1,3.469 true 2.198,3.833 2.74,3.698 true 1.083,2.625 1.406,2.802 0.323,0.177 10 false *b 1.979,2.635 2.385,2.833 0.406,0.198 10 false *c 0.625,3.115 0.833,3.302 0.208,0.188 10 false *a 0.813,3.76 1.094,3.958 0.281,0.198 10 false DL 2.802,3.604 3.083,3.802 0.281,0.198 10 false UL 1.667,3.094 1.875,3.281 0.208,0.188 10 false N1 0.604,3.385 1.052,3.594 0.448,0.208 10 false UNDL 2.615,3.354 2.896,3.552 0.281,0.198 10 false L
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.


Procedure 1

b.

Check the door lock motor operation.

Specified Condition:
Tester Connection Specified Condition

Click Location & Routing(N1)Location & Routing

Click Connector(N1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

N1-2 (L) - Auxiliary battery positive (+)
N1-1 (UL) - Auxiliary battery negative (-)
Lock
N1-1 (UL) - Auxiliary battery positive (+)
N1-2 (L) - Auxiliary battery negative (-)
Unlock
N1-4 (DL) - Auxiliary battery positive (+)
N1-3 (UNDL) - Auxiliary battery negative (-)
Sets
N1-3 (UNDL) - Auxiliary battery positive (+)
N1-4 (DL) - Auxiliary battery negative (-)
Unsets



c.

If the result is not as specified, replace the rear door lock assembly LH.


Post-procedure 1

d.

None


Pre-procedure 2

e.
B228544C11
1.563,3 1.979,3.25 0.417,0.25 0.958,4.125 1.354,4.125 true 2.177,4.115 2.573,4.115 true 2.177,4.438 2.021,4.135 true 1.406,4.438 1.531,4.156 true 0.823,3.104 0.99,3.26 0.167,0.156 10 false *a 2.396,2.656 2.552,2.802 0.156,0.146 10 false *b 1.385,2.656 1.542,2.802 0.156,0.146 10 false *c 1.167,4.458 1.719,4.635 0.552,0.177 10 false DLSR 0.792,4.042 0.906,4.188 0.115,0.146 10 false E 2.625,4.031 3.104,4.208 0.479,0.177 10 false LSSR 2.167,4.469 2.281,4.615 0.115,0.146 10 false E 1.677,3.052 2.156,3.229 0.479,0.177 10 false N1
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Measure the resistance according to the value(s) in the table below.


Procedure 2

f.

Check the operation of the door unlock detection switch.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N1)Location & Routing

Click Connector(N1)Body>No. 2 Rear Door Wire>Rear Door Lock with Motor Assembly LH

N1-5 (LSSR) - N1-6 (E) Lock 10 kΩ or higher
N1-5 (LSSR) - N1-6 (E) Unlock Below 1 Ω
N1-9 (DLSR) - N1-10 (E) Sets 10 kΩ or higher
N1-9 (DLSR) - N1-10 (E) Unsets Below 1 Ω



g.

If the result is not as specified, replace the rear door lock assembly LH.


Post-procedure 2

h.

None