Home › General › SPECIFICATIONS › M15A-FKS STARTING › from 2021.07
RM3700E _V1 General _093022 SPECIFICATIONS _0442319 M15A-FKS STARTING F

SPECIFICATIONS  M15A-FKS STARTING  SERVICE DATA  


Starter Assembly (w/ Stop and start system)
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A

Starter Assembly (w/o Stop and start system)
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A

Magnet start switch assembly (w/ Stop and start system)
Tester Connection Condition Specified Condition
Terminal 50 - Magnet starter switch assembly body Always Below 2 Ω

Magnet start switch assembly (w/o Stop and start system)
Tester Connection Condition Specified Condition
Terminal 50 - Magnet starter switch assembly body Always Below 2 Ω

Starter Armature Assembly (w/ Stop and start system)
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω
Segment - Starter armature core 10 kΩ or higher

Commutator runout Maximum runout 0.05 mm (0.00197 in.)

Commutator diameter Standard diameter 25.0 mm (0.984 in.)
Minimum diameter 24.0 mm (0.945 in.)

Undercut depth Standard undercut depth 0.7 mm (0.0276 in.)
Minimum undercut depth 0.2 mm (0.00787 in.)

Starter Armature Assembly (w/o Stop and start system)
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω
Segment - Starter armature core 10 kΩ or higher

Commutator runout Maximum runout 0.05 mm (0.00197 in.)

Commutator diameter Standard diameter 25.0 mm (0.984 in.)
Minimum diameter 24.0 mm (0.945 in.)

Undercut depth Standard undercut depth 0.7 mm (0.0276 in.)
Minimum undercut depth 0.2 mm (0.00787 in.)

Starter Brush Holder Assembly (w/ Stop and start system)
Brush length Standard length 11.6 mm (0.457 in.)
Minimum length 7.6 mm (0.299 in.)

Starter Brush Holder Assembly (w/o Stop and start system)
Brush length Standard length 11.6 mm (0.457 in.)
Minimum length 7.6 mm (0.299 in.)

Engine Switch
Tester Connection Condition Specified Condition

Click Location & Routing(H68)Location & Routing

Click Connector(H68)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Switch

H68-12(SS1) - H68-3(GND)
H68-6(SS2) - H68-3(GND)
H68-11(SS3) - H68-3(GND)
Not pushed 10 kΩ or higher
Pushed Below 1 Ω

Tester Connection Condition Specified Condition

Click Location & Routing(H68)Location & Routing

Click Connector(H68)Instrument Panel>Instrument Panel Wire / Speaker Wire>Engine Switch

H68-5(SWIL) - H68-3(GND) H68-5(SWIL) - Auxiliary battery positive (+)
H68-3(GND) - Auxiliary battery negative (-)
Illuminates

Ignition or Starter Switch Assembly
Tester Connection Condition Specified Condition

Click Location & Routing(H54)Location & Routing

Click Connector(H54)Instrument Panel>Instrument Panel Wire / Speaker Wire>Ignition Or Starter Switch Assembly

Between all terminals LOCK 10 kΩ or higher
H54-6 (ACC) - H54-7 (AM1) ACC Below 1 Ω
H54-6 (ACC) - H54-7 (AM1) - H54-8 (IG1) ON Below 1 Ω
H54-1 (AM2) - H54-[2] (IG2)
H54-[5] (ST1) - H54-7 (AM1) - H54-8 (IG1) START Below 1 Ω
H54-1 (AM2) - H54-[2] (IG2) - H54-4 (ST2)

ST No. 1 Relay
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω