Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › PRE-COLLISION SYSTEM › from 2021.07
RM3700E _95 ADAS / AD _095278 ADVANCED DRIVER ASSISTANCE SYSTEM _0447900 PRE-COLLISION SYSTEM D

ADVANCED DRIVER ASSISTANCE SYSTEM  PRE-COLLISION SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


a.

When a pre-collision system DTC is stored, the millimeter wave radar sensor assembly stores the current vehicle state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


a.

According to the GTS display, select a DTC that stored freeze frame data.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

b.

Read the freeze frame data recorded when the DTC was stored.



LIST OF FREEZE FRAME DATA


Body Electrical > Pre-Collision System
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - - - Cannot be used
Total Distance Traveled - Unit - - - Cannot be used
PCS Function ON/OFF State Status of the pre-collision system OFF switch ON / OFF ON: Pre-collision system enabled
OFF: Pre-collision system disabled
-
PBA Request Pre-collision brake assist operation status (While a control command is present, assist control operates when the driver depresses the brake pedal.) Not PBA Request / PBA Standby Request / PBA Request Level 1 / PBA Request Level 2 Not PBA Request: Pre-collision brake assist not requested
PBA Standby Request: Low pre-collision brake assist requested
PBA Request Level 1: Medium pre-collision brake assist requested
PBA Request Level 2: High pre-collision brake assist requested
The value changes in accordance with the possibility of a collision. This item indicates the pre-collision brake assist standby status. Whether pre-collision brake assist is applied or not is determined by the depression of the brake pedal.
VGRS Activation Request VGRS control activation start Not Request / VGRS 1 Request / VGRS 2 Request / VGRS 3 Request Not Request:
VGRS 1 Request: Request 1
VGRS 2 Request: Request 2
VGRS 3 Request: Request 3
This item is displayed on the GTS for vehicles without the VGRS system, but cannot be used
Warning Brake Request Warning brake operational status ON / OFF ON: Operating
OFF: Not operating
-
FPB Request for Gasoline Model:
Skid control ECU (brake actuator assembly) PCS brake request (pre-braking)
for HV Model:
Skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 PCS brake request (pre-braking)
ON / OFF ON: Operating
OFF: Not operating
-
PB Request Pre-collision brake request status ON / OFF ON: Operating
OFF: Not operating
-
AVS Control Request AVS control activation status ON / OFF ON: AVS control activated
OFF: AVS control not activated
This item is displayed on the GTS for vehicles without AVS, but cannot be used
Prefill for Gasoline Model:
Skid control ECU (brake actuator assembly) PCS brake assist standby
for HV Model:
Skid control ECU (brake booster with master cylinder assembly)*1 or skid control ECU (brake actuator assembly)*2 PCS brake assist standby
ON / OFF ON: Operating
OFF: Not operating
-
PBR Request PBR operation status ON / OFF ON: Operating
OFF: Not operating
-
PBH Request PBH operation status ON / OFF ON: Operating
OFF: Not operating
-
LPB Request LPB operation status ON / OFF ON: Operating
OFF: Not operating
-
PCS PBA Invalid Pre-collision brake assist function status ON / OFF ON: Pre-collision brake assist function invalid
OFF: Pre-collision brake assist function valid
-
PCS Warning Buzzer Invalid PCS warning buzzer status ON / OFF ON: PCS warning buzzer function invalid
OFF: PCS warning buzzer function valid
-
PCS PB Invalid PCS brake function status ON / OFF ON: PCS brake function invalid
OFF: PCS brake function valid
-
Acceleration Suppression at Low Speed (A Control) Invalid Acceleration suppression at low speed (A control) invalid status ON / OFF ON: Acceleration suppression at low speed (A control) function invalid
OFF: Acceleration suppression at low speed (A control) function valid
Cannot be used
Emergency Steering Assist Invalid 1 Emergency Steering Assist Invalid 1 status ON / OFF ON: Emergency steering assist invalid 1 function invalid
OFF: Emergency steering assist invalid 1 function valid
w/ Emergency steering assist
Emergency Steering Assist Invalid 2 Emergency Steering Assist Invalid 2 status ON / OFF ON: Emergency steering assist invalid 2 function invalid
OFF: Emergency steering assist invalid 2 function valid
w/ Emergency steering assist
PCS Warning Display Request PCS warning message status Not Request / PCS Warning Display 1 Request / PCS Warning Display 2 Request / PCS Warning Display 3 Request Not Request: Not displayed
PCS Warning Display 1 Request: Displayed
PCS Warning Display 2 Request: Not used
PCS Warning Display 3 Request: Not used
"BRAKE!" is displayed on multi-information display
PCS Warning Buzzer Request PCS meter buzzer operation status ON / OFF ON: Sounding
OFF: Not sounding
-
PCS Function ON/OFF State Stored Pre-collision system on/off setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. Stored / Not Stored Stored: PCS function remains OFF
Not Stored: PCS function resets to ON
"PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 2 Sensitivity setting when the pre-collision system is turned on and the ignition switch is turned off and then to ON. Stored / Not Stored Stored: Warning sensitivity is maintained at the previous value
Not Stored: Warning sensitivity resets to "Mid"
"PCS Warning Timing State Stored 2" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 3 Sensitivity setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. Stored / Not Stored Stored: Warning sensitivity is maintained at the previous value
Not Stored: Warning sensitivity resets to "Mid"
"PCS Warning Timing State Stored 3" is a customizable item which can be set using the GTS.
PCS Warning Timing State Stored 1 Sensitivity setting of the pre-collision system when the pre-collision system is turned off and the then on with the ignition switch ON. Stored / Not Stored Stored: Warning sensitivity is maintained at the previous value
Not Stored: Warning sensitivity resets to "Mid"
"PCS Warning Timing State Stored 1" is a customizable item which can be set using the GTS.

*1: for TMC Made

*2: for TMMF Made