Home › ADAS / AD › ADVANCED PARK › ADVANCED PARK › from 2021.07
RM3700E _95 ADAS / AD _105827 ADVANCED PARK _0485712 ADVANCED PARK C

ADVANCED PARK  ADVANCED PARK  U117987  Lost Communication with Image Processing Module "B" (ch2)  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
U117987 Lost Communication with Image Processing Module "B" (ch2) The clearance warning ECU assembly is unable to receive communication from the parking assist ECU
·

Open or short in bus main line

·

Clearance warning ECU assembly internal malfunction

·

Parking assist ECU internal malfunction

·

Parking assist ECU power source circuit malfunction


Clearance Warning A

WIRING DIAGRAM

E456285E04
1.094,0.792 1.542,0.979 0.448,0.188 10 false CAPH 5.667,0.781 6.115,0.969 0.448,0.188 10 false CAPH 5.677,1.49 6.125,1.677 0.448,0.188 10 false CAPL 1.125,1.479 1.573,1.667 0.448,0.188 10 false CAPL 1.625,0.75 2.073,0.938 0.448,0.188 10 false 6 1.625,1.24 2.073,1.427 0.448,0.188 10 false 7 5.354,0.781 5.594,0.969 0.24,0.188 10 false 35 5.354,1.24 5.594,1.427 0.24,0.188 10 false 36 5.344,1.729 5.688,1.938 0.344,0.208 10 false O60 5.344,1.906 6.906,2.281 1.563,0.375 10 false Clearance Warning ECU Assembly 0.521,1.729 0.958,1.948 0.438,0.219 10 false O118 0.521,1.917 1.833,2.198 1.313,0.281 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK CAN BUS MAIN WIRE (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O60,H3)Location & Routing

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O60-35 (CAPH) - O60-36 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
O60-35 (CAPH) - O60-36 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
O60-35 (CAPH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O60-36 (CAPL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O60-35 (CAPH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O60-36 (CAPL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Result Proceed to
O60-35 (CAPH) - O60-36 (CAPL) is more than or equal to 133 Ω A
O60-35 (CAPH) - O60-36 (CAPL) is less than 107 Ω B
O60-35 (CAPH) - H3-4 (CG) is less than 200 Ω C
O60-36 (CAPL) - H3-4 (CG) is less than 200 Ω D
O60-35 (CAPH) - H3-16 (BAT) is less than 6 kΩ E
O60-36 (CAPL) - H3-16 (BAT) is less than 6 kΩ F
None of the above conditions are met G



Post-procedure1

a.

None



A

2.CHECK CAN BUS WIRE (PARKING ASSIST ECU)

B

4.CHECK SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)

C

6.CHECK SHORT +B OR GROUND CAN BUS (PARKING ASSIST ECU)

D

6.CHECK SHORT +B OR GROUND CAN BUS (PARKING ASSIST ECU)

E

6.CHECK SHORT +B OR GROUND CAN BUS (PARKING ASSIST ECU)

F

6.CHECK SHORT +B OR GROUND CAN BUS (PARKING ASSIST ECU)

G

8.CLEAR DTC
2.CHECK CAN BUS WIRE (PARKING ASSIST ECU)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the parking assist ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O118)Location & Routing

Click Connector(O118)Body>Floor Wire>Parking Assist ECU

O118-6 (CAPH) - O118-7 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

3.CHECK CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
3.CHECK CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the parking assist ECU connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O60)Location & Routing

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

O60-35 (CAPH) - O60-36 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE

4.CHECK SHORT IN CAN BUS WIRES (PARKING ASSIST ECU)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O118)Location & Routing

Click Connector(O118)Body>Floor Wire>Parking Assist ECU

O118-6 (CAPH) - O118-7 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

5.CHECK SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
5.CHECK SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the parking assist ECU connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O60)Location & Routing

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

O60-35 (CAPH) - O60-36 (CAPL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE

6.CHECK SHORT +B OR GROUND CAN BUS (PARKING ASSIST ECU)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the parking assist ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O118,H3)Location & Routing

Click Connector(O118)Body>Floor Wire>Parking Assist ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O118-6 (CAPH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O118-7 (CAPL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O118-6 (CAPH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O118-7 (CAPL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

7.CHECK SHORT +B OR GROUND CAN BUS (CLEARANCE WARNING ECU ASSEMBLY)
7.CHECK SHORT +B OR GROUND CAN BUS (CLEARANCE WARNING ECU ASSEMBLY)

Pre-procedure1

a.

Reconnect the parking assist ECU connector.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the clearance warning ECU connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O60,H3)Location & Routing

Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assembly

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

O60-35 (CAPH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O60-36 (CAPL) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O60-35 (CAPH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O60-36 (CAPL) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE CAN BUS WIRE

8.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
U117987 is output A
DTCs are not output B
None of the above conditions are met C



A

10.REPLACE PARKING ASSIST ECU

B

C

GO TO DTC CHART

10.REPLACE PARKING ASSIST ECU

NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
U117987 is output A
DTCs are not output B
None of the above conditions are met C



A

B

END

C

GO TO DTC CHART