CLEARANCE WARNING ECU ASSEMBLY
Disconnect the O60 clearance warning ECU assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O60-1 (IG) - O60-31 (E) | IG power source signal | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V *1
10.5 to 16 V *2 |
||
| O60-31 (E) - Body ground | Ground | Always | Below 1 Ω |
*1: w/o Stop and Start System
*2: w/ Stop and Start System
Reconnect the O60 clearance warning ECU assembly connector.
Measure the voltage, resistance and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O60-2 (BOF) - O60-31 (E) | Power source for front sensor circuit | Ignition switch off | Below 1 V |
·
Ignition switch ON ·
TOYOTA parking assist-sensor system on |
11 to 14 V | ||
| O60-4 (SOF) - O60-31 (E) | Front sensor communication signal (Front clearance sonar sensor) | ·
Ignition switch ON ·
TOYOTA parking assist-sensor system on ·
Shift lever in any position other than P (for CVT) ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Pulse generation
(Refer to waveform 1) |
| O60-3 (E5) - O60-31 (E) | Ground for front clearance sonar | Always | Below 1 Ω |
| O60-9 (CBZ) - O60-8 (EF) | No. 1 clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
| O60-19 (BOR) - O60-31 (E) | Power source for rear sensor circuit | Ignition switch off | Below 1 V |
·
Ignition switch ON ·
TOYOTA parking assist-sensor system on |
11 to 14 V | ||
| O60-21 (SOR) - O60-31 (E) | Rear sensor communication signal (Rear clearance sonar sensor) | ·
Ignition switch ON ·
TOYOTA parking assist-sensor system on ·
Shift lever in R |
Pulse generation
(Refer to waveform 3) |
| O60-20 (E1) - O60-31 (E) | Ground for rear clearance sonar | Always | Below 1 Ω |
Using an oscilloscope, check waveform 1.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | O60-4 (SOF) - O60-31 (E) |
| Measurement setting | 1 V/DIV., 100 μs./DIV. |
| Condition | ·
Ignition switch ON ·
TOYOTA parking assist-sensor system on ·
Shift lever in any position other than P (for CVT) ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Using an oscilloscope, check waveform 2.
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | O60-9 (CBZ) - O60-8 (EF) |
| Measurement setting | 2 V/DIV., 500 μs./DIV. |
| Condition | Buzzer sounding |
The amplitude of the waveform changes according to the set volume.
Using an oscilloscope, check waveform 3.
Waveform 3 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | O60-21 (SOR) - O60-31 (E) |
| Measurement setting | 1 V/DIV., 100 μs./DIV. |
| Condition | ·
Ignition switch ON ·
TOYOTA parking assist-sensor system on ·
Shift lever in R |