Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485737 PANORAMIC VIEW MONITOR SYSTEM(w/o Advanced Park) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/o Advanced Park)  C1686  Driver Side Camera Video Sync Signal Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1686 Driver Side Camera Video Sync Signal Malfunction Side camera feedback malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E379403E27
5.708,2.813 6.167,3.01 0.458,0.198 10 false O25 5.708,2.979 7.031,3.385 1.323,0.406 10 false Parking Assist ECU 0.938,3.042 3.573,3.406 2.635,0.365 10 false Outer Rear View Mirror Assembly RH 0.74,2.375 3.156,2.625 2.417,0.25 10 false Side Television Camera Assembly RH 0.948,2.875 1.406,3.073 0.458,0.198 10 false K8 6.021,2.344 6.719,2.583 0.698,0.24 10 false SGND 6.021,1.927 6.719,2.167 0.698,0.24 10 false RGND 6.021,1.49 6.719,1.729 0.698,0.24 10 false RCV- 6,1.104 6.698,1.344 0.698,0.24 10 false RCV+ 6,0.656 6.698,0.896 0.698,0.24 10 false RCB+ 3.396,0.573 4.094,0.813 0.698,0.24 10 false RCB+ 3.385,0.958 4.083,1.198 0.698,0.24 10 false RCV+ 3.396,1.375 4.094,1.615 0.698,0.24 10 false RCV- 3.385,1.823 4.083,2.063 0.698,0.24 10 false RGND 5.75,0.594 6.063,0.792 0.313,0.198 10 false 6 5.688,1 6,1.198 0.313,0.198 10 false 30 5.688,1.396 6,1.594 0.313,0.198 10 false 31 5.698,1.833 6.01,2.031 0.313,0.198 10 false 23 5.708,2.24 6.021,2.438 0.313,0.198 10 false 32 3.906,1.802 4.219,2 0.313,0.198 10 false 13 3.906,1.375 4.219,1.573 0.313,0.198 10 false 14 3.917,0.958 4.229,1.156 0.313,0.198 10 false 6 3.906,0.573 4.219,0.771 0.313,0.198 10 false 5 4.781,2.302 4.938,2.5 0.156,0.198 10 false * 0.417,3.458 1.448,3.771 1.031,0.313 10 false *: Shielded 1.219,0.698 1.917,0.938 0.698,0.24 10 false SCB+ 1.208,1.125 1.906,1.365 0.698,0.24 10 false SCV+ 1.208,1.51 1.906,1.75 0.698,0.24 10 false SCV- 1.188,1.938 1.885,2.177 0.698,0.24 10 false SGND 0.75,2.208 1.021,2.438 0.271,0.229 10 false B 1.708,0.594 2.021,0.792 0.313,0.198 10 false 1 1.719,0.969 2.031,1.167 0.313,0.198 10 false 3 1.708,1.365 2.021,1.563 0.313,0.198 10 false 7 1.708,1.813 2.021,2.01 0.313,0.198 10 false 5


CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>CALIBRATION



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353
Result:
Proceed to
NEXT




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
Result:
Result Proceed to
DTCs are not output A
C1686 is output B




A

B

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)

Pre-procedure1

a.

Disconnect the O25 parking assist ECU connector.


b.

Disconnect the K8 outer rear view mirror assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25,K8)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

O25-6 (RCB+) - K8-5 (RCB+) Always Below 1 Ω
O25-30 (RCV+) - K8-6 (RCV+) Always Below 1 Ω
O25-31 (RCV-) - K8-14 (RCV-) Always Below 1 Ω
O25-23 (RGND) - K8-13 (RGND) Always Below 1 Ω
O25-6 (RCB+) or K8-5 (RCB+) - Body ground Always 10 kΩ or higher
O25-30 (RCV+) or K8-6 (RCV+) - Body ground Always 10 kΩ or higher
O25-31 (RCV-) or K8-14 (RCV-) - Body ground Always 10 kΩ or higher
O25-23 (RGND) or K8-13 (RGND) - Body ground Always 10 kΩ or higher
O25-32 (SGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK PARKING ASSIST ECU (RCV-, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK PARKING ASSIST ECU (RCV-, RGND)

Pre-procedure1

a.

Disconnect the O25 parking assist ECU connector.


Procedure1

a.
E432582C21
1.521,0.26 1.906,0.49 0.385,0.229 2.521,1.75 2.115,1.135 true 1.25,1.771 1.573,1.115 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 2.385,1.781 2.885,1.938 0.5,0.156 10 false RGND 1.115,1.802 1.615,1.958 0.5,0.156 10 false RCV- 1.583,0.281 2.083,0.438 0.5,0.156 10 false O25
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-23 (RGND) - Body ground Always Below 1 Ω
O25-31 (RCV-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

5.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.
E432581C28
1.417,0.25 1.917,0.5 0.5,0.25 2.604,1.833 2.125,1.146 true 2.146,0.99 2.719,0.365 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 2.792,0.302 3.188,0.458 0.396,0.156 10 false RCB+ 2.458,1.865 3.021,2.021 0.563,0.156 10 false RGND 1.531,0.271 2.135,0.5 0.604,0.229 10 false O25
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-23 (RGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-6 (RCB+) - O25-23 (RGND) Ignition switch ON 5.5 to 7.05 V
O25-6 (RCB+) - O25-23 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

NG

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY RH (RCV+, RGND)

Pre-procedure1

a.

Remove the parking assist ECU with the connector still connected.


Procedure1

a.

Using an oscilloscope, check the waveform of the side television camera assembly RH.

HINT:

A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


E444517C12
0.75,0.292 1.198,0.552 0.448,0.26 4.302,2.052 4.104,1.552 true 6.333,2.052 6.083,1.406 true 5.802,2.031 5.969,1.458 true 3.813,2.031 3.969,1.594 true 0.51,2 0.99,1.094 true 1.521,1.948 1.375,1.104 true 0.344,2.031 0.813,2.271 0.469,0.24 10 false RCV+ 1.396,1.99 1.875,2.167 0.479,0.177 10 false RGND 3.365,1.156 3.844,1.333 0.479,0.177 10 false GND 5.26,1.167 5.74,1.344 0.479,0.177 10 false GND 0.083,0.063 0.563,0.24 0.479,0.177 10 false *a 3.469,0.083 3.948,0.26 0.479,0.177 10 false *b 5.417,0.073 5.896,0.25 0.479,0.177 10 false *c 6.302,2.094 6.781,2.271 0.479,0.177 10 false *e 4.271,2.083 4.75,2.26 0.479,0.177 10 false *e 5.688,2.094 6.167,2.271 0.479,0.177 10 false *d 3.74,2.083 4.219,2.26 0.479,0.177 10 false *d 0.833,0.323 1.396,0.594 0.563,0.271 10 false O25
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


HINT:
·

The video waveform changes according to the image sent by the side television camera assembly RH.

·

The video waveform is constantly output when the ignition switch is ACC.



Measurement Condition
Item Content
Tester Connection O25-30 (RCV+) - O25-23 (RGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Ignition switch ON, panoramic view monitor switch on

OK:

Waveform is similar to that shown in illustration.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
7.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

Pre-procedure1

a.

Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


Procedure1

a.
E407112C44
1.521,0.083 1.875,0.313 0.354,0.229 0.323,2.281 0.823,2.531 0.5,0.25 0.99,0.375 1.24,0.375 1.24,0.375 1.427,0.76 true 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 1,1.427 1.25,1.427 1.25,1.427 1.427,1.104 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 1.448,1.823 1.698,1.823 1.698,1.823 1.781,2.438 true 2.323,1.802 2.073,1.802 2.073,1.802 1.958,2.427 true 2.281,3.177 2.031,3.177 2.031,3.177 1.948,2.688 true 1.417,3.156 1.667,3.156 1.667,3.156 1.792,2.688 true 1.052,1.708 1.667,1.906 0.615,0.198 10 false RCB+ 2.469,0.271 3.083,0.469 0.615,0.198 10 false SCB+ 0.563,0.281 1.177,0.479 0.615,0.198 10 false SCV+ 0.604,1.333 1.219,1.531 0.615,0.198 10 false SCV- 2.49,1.323 3.104,1.521 0.615,0.198 10 false SGND 2.396,1.698 3.01,1.896 0.615,0.198 10 false RCV+ 0.969,3.052 1.583,3.25 0.615,0.198 10 false RGND 2.354,3.052 2.969,3.25 0.615,0.198 10 false RCV- 1.656,0.115 2.271,0.313 0.615,0.198 10 false B 0.479,2.313 1.094,2.51 0.615,0.198 10 false K8 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(K8)Location & Routing

Click Connector(K8)Body>Front Door Wire RH / Television Camera Wire>Outer Rear View Mirror Assembly RH

B-1 (SCB+) - K8-5 (RCB+) Always Below 1 Ω
B-3 (SCV+) - K8-6 (RCV+) Always Below 1 Ω
B-7 (SCV-) - K8-14 (RCV-) Always Below 1 Ω
B-5 (SGND) - K8-13 (RGND) Always Below 1 Ω
B-1 (SCB+) or K8-5 (RCB+) - Body ground Always 10 kΩ or higher
B-3 (SCV+) or K8-6 (RCV+) - Body ground Always 10 kΩ or higher
B-7 (SCV-) or K8-14 (RCV-) - Body ground Always 10 kΩ or higher
B-5 (SGND) or K8-13 (RGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

8.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Clear the DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353
Result:
Proceed to
NEXT




NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs.

HINT:

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>DTC CHECK / CLEAR


Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
Result:
Result Proceed to
DTCs are not output A
C1686 is output B




A

END (SIDE TELEVISION CAMERA ASSEMBLY RH WAS DEFECTIVE)

B