Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485737 PANORAMIC VIEW MONITOR SYSTEM(w/o Advanced Park) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/o Advanced Park)  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E403285E11
0.281,1.01 1.813,1.313 1.531,0.302 10 false from Auxiliary Battery 0.271,2.104 2.26,2.302 1.99,0.198 10 false from IGR-NO. 1 Relay 0.615,2.656 2.604,2.854 1.99,0.198 10 false from ACC Relay 1.99,1.198 3.198,1.521 1.208,0.323 10 false ECU-DCC NO. 2 2.073,2.271 3.135,2.583 1.063,0.313 10 false ECU-IGR NO. 1 2.198,2.844 3.031,3.083 0.833,0.24 10 false ECU-ACC 5.313,0.906 5.469,1.104 0.156,0.198 10 false 1 5.281,1.99 5.5,2.188 0.219,0.198 10 false 21 5.323,2.552 5.479,2.75 0.156,0.198 10 false 3 5.323,3.052 5.479,3.25 0.156,0.198 10 false 2 5.552,1.031 5.865,1.229 0.313,0.198 10 false +B 5.573,2.104 5.885,2.302 0.313,0.198 10 false IG 5.552,2.667 6.01,2.865 0.458,0.198 10 false ACC 5.542,3.156 6.156,3.354 0.615,0.198 10 false GND1 5.271,3.844 5.646,4.01 0.375,0.167 10 false O25 5.26,4.01 6.667,4.323 1.406,0.313 10 false Parking Assist ECU 5.552,1.552 5.865,1.75 0.313,0.198 10 false +B2 5.271,1.438 5.49,1.635 0.219,0.198 10 false 19 5.542,3.521 6.156,3.719 0.615,0.198 10 false GND2 5.292,3.406 5.51,3.604 0.219,0.198 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>CALIBRATION

·

Inspect the fuse for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.

Disconnect the O25 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-2 (GND1) - Body ground Always Below 1 Ω
O25-20 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O25)Location & Routing

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

O25-1 (+B) - O25-2 (GND1) Ignition switch off 11 to 14 V
O25-19 (+B2) - O25-2 (GND1) Ignition switch off 11 to 14 V
O25-3 (ACC) - O25-2 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
O25-21 (IG) - O25-2 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR