Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485736 PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park)  ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the parking assist ECU. The parking assist ECU controls the panoramic view monitor system.

WIRING DIAGRAM

E301406E98
5.302,2.844 6.594,3.063 1.292,0.219 10 false Parking Assist ECU 5.292,2.698 5.667,2.885 0.375,0.188 10 false O118 5.302,2.125 5.74,2.333 0.438,0.208 10 false GND1 5.313,1.708 5.688,1.896 0.375,0.188 10 false ACC 5.302,1.302 5.51,1.49 0.208,0.188 10 false IG 5.302,0.865 5.563,1.063 0.26,0.198 10 false +B 5.104,0.781 5.26,0.979 0.156,0.198 10 false 1 5.115,1.188 5.271,1.385 0.156,0.198 10 false 3 5.104,1.625 5.26,1.823 0.156,0.198 10 false 2 5.125,2.021 5.281,2.219 0.156,0.198 10 false 4 3.208,1.052 4.229,1.25 1.021,0.198 10 false ECU-DCC NO. 2 3.208,1.49 4.281,1.688 1.073,0.198 10 false ECU-IGR NO. 1 3.323,1.917 4.198,2.125 0.875,0.208 10 false ECU-ACC 0.896,0.896 2.25,1.125 1.354,0.229 10 false from Auxiliary Battery 0.865,1.302 2.333,1.521 1.469,0.219 10 false from IGR-NO. 1 Relay 1.24,1.708 2.292,1.948 1.052,0.24 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following procedure.


HINT:

If the parking assist ECU does not operate due to a power source problem, other system DTCs may be stored due to a CAN communication interruption.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.

Disconnect the O118 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O118)Location & Routing

Click Connector(O118)Body>Floor Wire>Parking Assist ECU

O118-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(O118)Location & Routing

Click Connector(O118)Body>Floor Wire>Parking Assist ECU

O118-1 (+B) - O118-4 (GND1) Ignition switch off 11 to 14 V
O118-2 (ACC) - O118-4 (GND1) Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
O118-3 (IG) - O118-4 (GND1) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR