Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › from 2021.07
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441967 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

w/ Wireless Door Lock Buzzer Answer-back Function:

If the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM will store this DTC.


w/o Wireless Door Lock Buzzer Answer-back Function:

If the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM will store this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
B279A12 Engine Immobiliser System Circuit Short to Battery
w/ Wireless Door Lock Buzzer Answer-back Function:

The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high. (1 trip detection logic*)


w/o Wireless Door Lock Buzzer Answer-back Function:

The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high. (1 trip detection logic*)


w/ Wireless Door Lock Buzzer Answer-back Function:
·

Certification ECU (smart key ECU assembly)

·

ECM

·

Wire harness or connector


w/o Wireless Door Lock Buzzer Answer-back Function:
·

ID code box (immobiliser code ECU)

·

ECM

·

Wire harness or connector


Engine A DTC output confirmation operation:

Turn the ignition switch to ON and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

w/ Wireless Door Lock Buzzer Answer-back Function


B463091E56
0.417,1.865 2.271,2.135 1.854,0.271 10 false ECM 0.417,1.698 0.875,1.896 0.458,0.198 10 false A54 0.854,0.219 1.313,0.417 0.458,0.198 10 false +B 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 2.635,0.917 0.458,0.198 10 false 61 4.917,0.719 5.375,0.917 0.458,0.198 10 false 5 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false H45 5.125,1.844 6.927,2.26 1.802,0.417 10 false Certification ECU (Smart Key ECU Assembly)


w/o Wireless Door Lock Buzzer Answer-back Function


B463091E92
0.51,1.865 2.365,2.135 1.854,0.271 10 false ECM 0.51,1.698 1.031,1.927 0.521,0.229 10 false A54 0.854,0.219 1.313,0.417 0.458,0.198 10 false +B 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 3.292,0.917 1.115,0.198 10 false 61 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false H67 5.125,1.844 6.698,2.229 1.573,0.385 10 false ID Code Box (Immobiliser Code ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to the Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

*1: w/ Wireless Door Lock Buzzer Answer-back Function

*2: w/o Wireless Door Lock Buzzer Answer-back Function




HINT:

When DTC B279A12 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Wireless Door Lock Buzzer Answer-back Function A
w/o Wireless Door Lock Buzzer Answer-back Function B



A

2.CHECK CONNECTION OF CONNECTOR

B

5.CHECK CONNECTION OF CONNECTOR
2.CHECK CONNECTION OF CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B574558C06
2.167,0.042 2.594,0.292 0.427,0.25 1.74,1.531 1.938,0.615 true 3.073,3.552 3.229,3.021 true 3.573,3.542 3.427,3.031 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 2.26,0.094 2.573,0.25 0.313,0.156 10 false H45 1.344,1.448 1.865,1.656 0.521,0.208 10 false EFIO
*a Component with harness connected
Certification ECU (Smart Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H45)Location & Routing

Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

H45-5 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal wavform C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the A54 ECM connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A54,H45)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECU

A54-61 (IMO) - H45-4 (EFII) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTION OF CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

6.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

NG

CONNECT CONNECTORS PROPERLY

6.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

E446705C07
3.292,0.094 3.719,0.344 0.427,0.25 3.083,3.542 3.219,3.042 true 3.563,3.531 3.417,3.042 true 2.906,1.583 3.385,0.896 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 3.375,0.146 3.688,0.302 0.313,0.156 10 false H67 2.521,1.5 3.042,1.708 0.521,0.208 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H67)Location & Routing

Click Connector(H67)Instrument Panel>Instrument Panel Wire / Speaker Wire>ID Code Box

H67-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal wavform C



A

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

B

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the A54 ECM connector.


b.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A54,H67)Location & Routing

Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECM

Click Connector(H67)Instrument Panel>Instrument Panel Wire / Speaker Wire>ID Code Box

A54-61 (IMI) - H67-4 (EFIO) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR