Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Adaptive High Beam System) › from 2021.07
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0486937 LIGHTING SYSTEM(w/ Adaptive High Beam System) D

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Adaptive High Beam System)  OPERATION CHECK  


AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK


NOTICE:

Make sure that the customize settings are set to default when performing the automatic light control system operation check.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>CUSTOMIZE PARAMETERS


a.

Turn the ignition switch to ON.


b.

Turn the light control switch to the AUTO position.


c.

Cover the automatic light control sensor.


d.

Check that the taillights and low beam headlights come on.


e.

Uncover the automatic light control sensor.


f.

Check that the low beam headlights and taillights turn off.



LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK


a.

When the light control switch is in the AUTO position

i.

Turn the ignition switch to ON.


ii.

Turn the taillights, low beam headlights, high beam headlights , front fog lights* and rear fog lights on.

*: w/ Front Fog Light



iii.

Turn the ignition switch off.

HINT:

If the vehicle speed was not less than 10 km/h (6 mph) when the ignition switch was turned off, open the driver door.



iv.

Check that all of the lights turn off immediately.



b.

When the light control switch is in the tail or head position

i.

Turn the ignition switch to ON.


ii.

Turn the low beam headlights and high beam headlights on.


iii.

Turn the ignition switch off.

HINT:

If the vehicle speed was not less than 10 km/h (6 mph) when the ignition switch was turned off, open the driver door.



iv.

Check that the low beam headlights and high beam headlights turn off immediately.

HINT:

The taillights, clearance lights and license plate lights remain on.





DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK


a.

Turn the ignition switch to ON (READY).*1


b.

Start the engine.*2


c.

Turn the light control switch to the tail or AUTO position (with the low beam headlights not turned on via the automatic light control system).


d.

Release the parking brake.


e.

Check that the daytime running lights come on.

*1: for HV Model

*2: for Gasoline Model




WELCOME LIGHT ILLUMINATION CONTROL OPERATION CHECK


NOTICE:

Make sure that the customize settings are set to default when performing the welcome light illumination control operation check.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>CUSTOMIZE PARAMETERS


a.

Check that welcome light illumination turns on.

i.

Turn the ignition switch off.


ii.

Set the light control switch to the HEAD position and then to the AUTO position.


iii.

Cover the automatic light control sensor.


iv.

Close and lock all doors.


v.

Unlock all doors by wireless door unlock or entry door unlock.


vi.

Check that the taillights, clearance lights and license plate lights come on for 15 seconds.



b.

Check that welcome light illumination turns off.

i.

After the light is illuminated, the clearance lights are turned off when either of the following conditions is met before 15 seconds have elapsed.

·

The ignition switch is to ON.

·

The light control switch is in any position except the AUTO position.

·

Door lock is performed.





EXTENDED HEADLIGHT LIGHTING SYSTEM OPERATION CHECK


NOTICE:

Make sure that the customize settings are set to default when performing the extended headlight lighting system operation check.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Adaptive High Beam System)>CUSTOMIZE PARAMETERS


a.

Turn the ignition switch off.


b.

Turn the light control switch to the AUTO position.


c.

Pull the dimmer switch to flash the headlights once.


d.

Check that the low beam headlights come on for approximately 30 seconds.



AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM OPERATION CHECK


a.

Stop the vehicle on a level surface and keep the vehicle height unchanged.


b.

Turn the ignition switch to ON (READY).*1


c.

Start the engine.*2


d.

Check that the headlight leveling motors operate.



*1: for HV Model

*2: for Gasoline Model