This is the power source circuit to operate the radio and display receiver assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Stop and Start System | A |
| w/ Stop and Start System | B |
A
B
Disconnect the H79 and H80 radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H79)Location & Routingewd_type=routing;type=c;code=H79 Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H79;pinno=1 |
||
| H79-1 (GND1) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H79,H80)Location & Routingewd_type=routing;type=c,c;code=H79,H80 Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H79;pinno=4,1,15 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=19 |
||
| H79-4 (+B1) - H79-1 (GND1) | Ignition switch off | 11 to 14 V |
| H79-15 (ACC1) - H79-1 (GND1) | Ignition switch ACC | 11 to 14 V |
| H80-19 (IG) - H79-1 (GND1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H79 and H80 radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H79)Location & Routingewd_type=routing;type=c;code=H79 Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H79;pinno=1 |
||
| H79-1 (GND1) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H79,H80)Location & Routingewd_type=routing;type=c,c;code=H79,H80 Click Connector(H79)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H79;pinno=4,1,15 Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H80;pinno=19 |
||
| H79-4 (+B1) - H79-1 (GND1) | Ignition switch off | 10.5 to 16 V |
| H79-15 (ACC1) - H79-1 (GND1) | Ignition switch ACC | 10.5 to 16 V |
| H80-19 (IG) - H79-1 (GND1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING