If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.
The Navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the Navigation system will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B1543 | Extension Module Disconnected 2 | Navigation ECU disconnected | ·
Navigation ECU ·
Radio and display receiver assembly ·
Harness or connector |
Navigation System | A |
This DTC may be stored due to environmental reasons such as electrical noise or interference.
Inspect the fuses for circuits related to this system before performing the following procedure.
Turn the ignition switch to ACC and wait for 90 seconds.
Press the "MAP" switch and check that the map screen is displayed normally.
| Result | Proceed to |
|---|---|
| Map screen is displayed normally | A |
| Map screen is not displayed normally | B |
This DTC may be stored due to environmental reasons such as electrical noise or interference.
Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Stop and Start System | A |
| w/ Stop and Start System | B |
A
B
Pre-procedure1
Disconnect the H82 navigation ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H82)Location & Routingewd_type=routing;type=c;code=H82 Click Connector(H82)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECUewd_type=component;type=c;code=H82;pinno=23 |
||
| H82-23 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H82)Location & Routingewd_type=routing;type=c;code=H82 Click Connector(H82)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECUewd_type=component;type=c;code=H82;pinno=10 |
||
| H82-10 (+B) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the H122 navigation ECU connector.
Disconnect the H123 radio and display receiver assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H122,H123)Location & Routingewd_type=routing;type=c,c;code=H122,H123 Click Connector(H122)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECUewd_type=component;type=c;code=H122;pinno=4,5,6 Click Connector(H123)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H123;pinno=1,2,3 |
||
| H122-4 (US4+) - H123-1 (US4+) | Always | Below 1 Ω |
| H122-5 (US4-) - H123-2 (US4-) | Always | Below 1 Ω |
| H122-6 (UGD4) - H123-3 (UGD4) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the navigation ECU with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Pre-procedure1
Disconnect the H82 navigation ECU connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H82)Location & Routingewd_type=routing;type=c;code=H82 Click Connector(H82)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECUewd_type=component;type=c;code=H82;pinno=23 |
||
| H82-23 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H82)Location & Routingewd_type=routing;type=c;code=H82 Click Connector(H82)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECUewd_type=component;type=c;code=H82;pinno=10 |
||
| H82-10 (+B) - Body ground | Ignition switch off | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Pre-procedure1
Disconnect the H122 navigation ECU connector.
Disconnect the H123 radio and display receiver assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H122,H123)Location & Routingewd_type=routing;type=c,c;code=H122,H123 Click Connector(H122)Instrument Panel>Instrument Panel Wire / Speaker Wire>Navigation ECUewd_type=component;type=c;code=H122;pinno=4,5,6 Click Connector(H123)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assemblyewd_type=component;type=c;code=H123;pinno=1,2,3 |
||
| H122-4 (US4+) - H123-1 (US4+) | Always | Below 1 Ω |
| H122-5 (US4-) - H123-2 (US4-) | Always | Below 1 Ω |
| H122-6 (UGD4) - H123-3 (UGD4) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the navigation ECU with a new one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B