Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093687 NAVIGATION / MULTI INFO DISPLAY _0441739 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

This circuit is from the brake actuator assembly to the radio and display receiver assembly.

WIRING DIAGRAM

E450792E12
0.063,0.042 3.729,0.281 3.667,0.24 12 false for TMMF Made: 0.781,1.688 1.24,1.885 0.458,0.198 10 false A35 1.646,0.979 2.104,1.177 0.458,0.198 10 false PKB 2.073,0.875 2.531,1.073 0.458,0.198 10 false 35 0.771,1.854 3.156,2.167 2.385,0.313 10 false Brake Actuator Assembly 4.896,0.875 5.354,1.073 0.458,0.198 10 false 20 5.167,0.99 5.625,1.188 0.458,0.198 10 false PKB 4.885,1.688 5.49,1.979 0.604,0.292 10 false H80 4.885,1.896 6.594,2.375 1.708,0.479 10 false Radio and Display Receiver Assembly

E450792E07
0.042,0.042 3.708,0.281 3.667,0.24 12 false for Gasoline Model TMC Made: 0.781,1.688 1.24,1.885 0.458,0.198 10 false A94 1.646,0.979 2.104,1.177 0.458,0.198 10 false PKB 2.052,0.854 2.51,1.052 0.458,0.198 10 false 24 0.771,1.854 3.156,2.167 2.385,0.313 10 false Brake Actuator Assembly 4.896,0.875 5.354,1.073 0.458,0.198 10 false 20 5.167,0.99 5.625,1.188 0.458,0.198 10 false PKB 4.885,1.688 5.49,1.979 0.604,0.292 10 false H80 4.885,1.896 6.594,2.375 1.708,0.479 10 false Radio and Display Receiver Assembly

E450792E08
0.063,0.052 2.313,0.365 2.25,0.313 12 false for HV Model TMC Made: 0.771,1.677 1.229,1.875 0.458,0.198 10 false A95 0.771,1.823 2.542,2.115 1.771,0.292 10 false Brake Actuator Assembly 1.656,0.969 2.115,1.167 0.458,0.198 10 false PKB 5.177,0.979 5.635,1.177 0.458,0.198 10 false PKB 2.063,0.854 2.521,1.052 0.458,0.198 10 false 19 4.885,0.854 5.344,1.052 0.458,0.198 10 false 20 4.917,1.688 6.844,1.979 1.927,0.292 10 false H80 4.906,1.865 6.604,2.333 1.698,0.469 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK BRAKE WARNING LIGHT
a.

Check that the brake warning light comes on when the parking brake is applied and goes off when it is released.

OK:

The brake warning light operates as specified above.



Result:
Result Proceed to
OK (for TMMF Made) A
OK (for Gasoline Model TMC Made) B
OK (for HV Model TMC Made) C
NG D



A

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

D

2.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the A39 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80,A39)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(A39)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

H80-20 (PKB) - A39-35 (PKB) Always Below 1 Ω
H80-20 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the A94 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80,A94)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

H80-20 (PKB) - A94-24 (PKB) Always Below 1 Ω
H80-20 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the A95 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H80,A95)Location & Routing

Click Connector(H80)Instrument Panel>Instrument Panel Wire / Speaker Wire>Radio & Display Receiver Assembly

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

H80-20 (PKB) - A95-19 (PKB) Always Below 1 Ω
H80-20 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR