DTC B228231 is stored when the vehicle speed signal sent by the skid control ECU via direct line and the vehicle speed signal sent via CAN communication do not match.
DTC B228262 is stored when a malfunction in the vehicle speed sensor is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B228231 | Vehicle Speed Signal Circuit Open | The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. (1-trip detection logic*) | ·
Electronically controlled brake system ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
Power Source Control | A | DTC Output Confirmation Operation:
Drive the vehicle at a vehicle speed of 25 km/h (16 mph) or more for 20 seconds, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds. |
| B228262 | Vehicle Speed Signal Compare Failure | Vehicle speed signal malfunction is detected (excessive deceleration is detected). (1-trip detection logic*) | ·
Electronically controlled brake system ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
Power Source Control | A | DTC Output Confirmation Operation:
Drive the vehicle at a vehicle speed of 50 km/h (31 mph) or more for 10 seconds, and then drive the vehicle at a vehicle speed of less than 50 km/h (31 mph). |
*: Only detected while a malfunction is present and the ignition switch is ON.
| DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|---|
| B228231 | ·
When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior. ·
When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the ignition switch cannot be turned from ON to off. |
- |
| B228262 | ·
The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven. ·
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine will not start. |
Steering lock motor operation is prohibited. |
| DTC No. | Data List and Active Test |
|---|---|
| B228231
B228262 |
Power Source Control
·
Vehicle Running Condition (Line) ·
Power Supply Condition Brake/EPB
·
Vehicle Speed |
for TMC Made
for TMMF Made
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| Vehicle Speed |
Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the GTS.
Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for TMC Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>HOW TO PROCEED WITH TROUBLESHOOTING
for TMMF Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>HOW TO PROCEED WITH TROUBLESHOOTING
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Running Condition (Line) | Vehicle being driven or stopped | Stop or Running | Stop: Vehicle stopped
Driving: Vehicle being driven at 5 km/h (3 mph) or more |
- |
| Tester Display |
|---|
| Vehicle Running Condition (Line) |
| Result | Proceed to |
|---|---|
| The value of Vehicle Running Condition (Line) is Stop | A |
| The value of Vehicle Running Condition (Line) is not Stop | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Running Condition (Line) | Vehicle being driven or stopped | Stop or Running | Stop: Vehicle stopped
Running: Vehicle being driven at 5 km/h (3 mph) or more |
- |
| Tester Display |
|---|
| Vehicle Running Condition (Line) |
| Result | Proceed to |
|---|---|
| The value of Vehicle Running Condition (Line) is Running | A |
| The value of Vehicle Running Condition (Line) is not Running | B |
A
for TMC Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>HOW TO PROCEED WITH TROUBLESHOOTING
for TMMF Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Disconnect the A94 skid control ECU (brake actuator assembly) connector.
Disconnect the H45 certification ECU (smart key ECU assembly) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H45,A94)Location & Routingewd_type=routing;type=c,c;code=H45,A94 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=13 Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A94;pinno=18 |
||
| H45-13 (SPD) - A94-18 (SP1) | Always | Below 1 Ω |
| H45-13 (SPD) or A94-18 (SP1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect the H45 certification ECU (smart key ECU assembly) connector.
Connect the A38 skid control ECU (brake actuator assembly) connector.
Procedure1
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
|
Click Location & Routing(H45,H46)Location & Routingewd_type=routing;type=c,c;code=H45,H46 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=13 Click Connector(H46)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H46;pinno=29 |
|||
| H45-13 (SPD) - H46-29 (E) | Ignition switch ON, vehicle being driven at approx. 5 km/h (3 mph) | 5 V/DIV., 20 ms./DIV. | Pulse generation
(See waveform) |
The wavelength becomes shorter as the vehicle speed increases.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
for TMC Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>HOW TO PROCEED WITH TROUBLESHOOTING
for TMMF Made: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>HOW TO PROCEED WITH TROUBLESHOOTING