Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0444943 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B15C511  Emergency Call Switch Circuit Short to Ground  B15C513  Emergency Call Switch Circuit Open  


DESCRIPTION

If the telematics transceiver detects an error in the communication between the telematics transceiver and the map light assembly (manual (SOS) switch) as a result of the telematics transceiver self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B15C511 Emergency Call Switch Circuit Short to Ground Manual (SOS) switch impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Map light assembly

·

Harness or connector

·

Telematics transceiver


Telematics A
B15C513 Emergency Call Switch Circuit Open Manual (SOS) switch impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Map light assembly

·

Harness or connector

·

Telematics transceiver


Telematics A

WIRING DIAGRAM

E231377E89
0.646,2.083 1.042,2.271 0.396,0.188 10 false H85 5.052,2.063 5.448,2.25 0.396,0.188 10 false V7 0.646,2.25 2.844,2.49 2.198,0.24 10 false Telematics Transceiver 5.052,2.208 6.865,2.615 1.813,0.406 10 false Map Light Assembly (Manual (SOS) Switch) 5.375,0.792 5.771,0.979 0.396,0.188 10 false SIG1 5.396,1.594 5.823,1.781 0.427,0.188 10 false GND3 1.438,0.792 1.833,0.979 0.396,0.188 10 false SIG1 1.448,1.594 1.802,1.781 0.354,0.188 10 false SIG- 1.844,0.698 2.094,0.885 0.25,0.188 10 false 21 1.844,1.479 2.094,1.667 0.25,0.188 10 false 3 5.135,0.667 5.344,0.854 0.208,0.188 10 false 12 5.198,1.469 5.406,1.656 0.208,0.188 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
B15C511 or B15C513 is output B
None of the above conditions are met C



A

B

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

C

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

Pre-procedure1

a.

Remove the map light assembly (manual (SOS) switch).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



Procedure1

a.
E434371C16
1.531,0.302 1.958,0.552 0.427,0.25 1.115,1.677 1.375,1.26 true 2.667,1.646 2.667,1.271 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 2.542,1.688 2.99,1.938 0.448,0.25 10 false GND3 0.958,1.729 1.406,1.979 0.448,0.25 10 false SIG1 1.656,0.365 1.969,0.563 0.313,0.198 10 false V7
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V7)Location & Routing

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

V7-12 (SIG1) - V7-5 (GND3) Manual (SOS) switch not operated 407.8 to 416.1 Ω
V7-12 (SIG1) - V7-5 (GND3) Manual (SOS) switch operated 81.1 to 82.8 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

Pre-procedure1

a.

Disconnect the H85 telematics transceiver connector.


b.

Disconnect the V7 map light assembly (manual (SOS) switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85,V7)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

H85-21 (SIG1) - V7-12 (SIG1) Always Below 1 Ω
H85-3 (SIG-) - V7-5 (GND3) Always Below 1 Ω
H85-21 (SIG1) or V7-12 (SIG1) - Body ground Always 10 kΩ or higher
H85-3 (SIG-) or V7-5 (GND3) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL



Result:
Proceed to
NEXT



NEXT