Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0444943 TELEMATICS SYSTEM(for Toyota Connected Services) J

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E418549E93
2.385,2.229 2.854,2.396 0.469,0.167 10 false H85 2.375,2.396 3.833,2.646 1.458,0.25 10 false Telematics Transceiver 4.563,2.615 4.938,2.823 0.375,0.208 10 false V7 4.552,2.781 6.542,3.167 1.99,0.385 10 false Map Light Assembly 4.24,0.896 4.5,1.115 0.26,0.219 10 false 8 4.25,1.698 4.563,1.938 0.313,0.24 10 false 5 4.458,0.906 4.844,1.083 0.385,0.177 10 false RRID 1.083,1.031 2.635,1.313 1.552,0.281 10 false from IGR-NO. 2 Relay 4.458,1.719 4.927,1.896 0.469,0.177 10 false GND3 4.969,2.135 6.417,2.313 1.448,0.177 10 false Manual (SOS) Switch 2.823,1.198 3.938,1.396 1.115,0.198 10 false ECU-IGR NO. 2 3.292,1.823 3.76,2 0.469,0.177 10 false SIG- 3.708,1.708 4.021,1.948 0.313,0.24 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



HINT:

Inspect the fuses and relays related to this system before inspecting the suspected areas below.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) POWER SOURCE)
a.

Disconnect the H85 telematics transceiver connector.


b.

Disconnect the V7 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85,V7)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

H85-3 (SIG-) - V7-5 (GND3) Always Below 1 Ω
H85-3 (SIG-) or V7-5 (GND3) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(V7)Location & Routing

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

V7-8 (RRID) - Body Ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
E434371C17
1.469,0.24 1.906,0.49 0.438,0.25 2.677,1.646 2.656,1.26 true 1.833,1.646 2.146,1.271 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.521,1.667 3.042,1.885 0.521,0.219 10 false GND3 1.563,1.667 2,1.875 0.438,0.208 10 false RRID 1.604,0.292 1.917,0.49 0.313,0.198 10 false V7
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Apply auxiliary battery voltage to the connector.

Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → V7-8 (RRID)
Auxiliary battery negative (-) → V7-5 (GND3)
Always Manual (SOS) switch illumination comes on


c.

Check if the manual (SOS) switch illumination comes on.

OK:

The manual (SOS) switch illumination comes on.



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY

3.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL


Result:
Proceed to
NEXT



NEXT