Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0444943 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B157111  Indicator (Green) Circuit Short to Ground  B157113  Indicator (Green) Circuit Open  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.

If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B157111 Indicator (Green) Circuit Short to Ground Manual (SOS) switch indicator (green) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Harness or connector


Telematics A
B157113 Indicator (Green) Circuit Open Manual (SOS) switch indicator (green) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Harness or connector


Telematics A

WIRING DIAGRAM

E427069E52
4.844,1.917 6.354,2.167 1.51,0.25 10 false Telematics Transceiver 4.844,1.75 6.833,1.948 1.99,0.198 10 false H85 5.177,0.792 6.5,1.135 1.323,0.344 10 false IND2 4.885,0.667 6.208,1.01 1.323,0.344 10 false 22 5.177,1.104 6.5,1.448 1.323,0.344 10 false SIG- 4.938,1.094 6.26,1.438 1.323,0.344 10 false 3 3.427,0.667 4.75,1.01 1.323,0.344 10 false 7 3.406,1.083 4.729,1.427 1.323,0.344 10 false 5 3.021,0.667 4.344,1.01 1.323,0.344 10 false IND2 2.948,1.094 4.271,1.438 1.323,0.344 10 false GND3 1.271,1.771 2.594,2.115 1.323,0.344 10 false V7 1.271,1.917 3.99,2.146 2.719,0.229 10 false Map Light Assembly (Manual (SOS) Switch)

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
B157111 or B157113 is output B
None of the above conditions are met C



A

B

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

C

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

Pre-procedure1

a.

Remove the map light assembly (manual (SOS) switch).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



b.

Connect 2 dry-cell batteries (1.5 V each) in series.


Procedure1

a.
E434371C15
1.448,0.271 1.906,0.531 0.458,0.26 2.406,1.25 2.208,1.698 true 2.677,1.271 2.823,1.76 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.688,1.792 3.208,2.01 0.521,0.219 10 false GND3 2.01,1.729 2.448,1.938 0.438,0.208 10 false IND2 1.594,0.323 1.906,0.521 0.313,0.198 10 false V7
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Connect a positive (+) lead from batteries to terminal 7 (IND2) and a negative (-) lead to terminal 5 (GND3) of the map light assembly (manual (SOS) switch) connector.


b.

Check if the manual (SOS) switch green indicator comes on.

OK:

Manual (SOS) switch green indicator illuminates.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

Pre-procedure1

a.

Disconnect the H85 telematics transceiver connector.


b.

Disconnect the V7 map light assembly (manual (SOS) switch) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H85,V7)Location & Routing

Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiver

Click Connector(V7)Body>No. 1 Roof Wire>Map Light Assembly

H85-22 (IND2) - V7-7 (IND2) Always Below 1 Ω
H85-22 (IND2) or V7-7 (IND2) - Body ground Always 10 kΩ or higher
H85-3 (SIG-) - V7-5 (GND3) Always Below 1 Ω
H85-3 (SIG-) or V7-5 (GND3) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL



Result:
Proceed to
NEXT



NEXT