Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › from 2021.07
RM3700E _58 Vehicle Interior _093748 THEFT DETERRENT / KEYLESS ENTRY _0441966 ENTRY AND START SYSTEM(for Start Function, HV Model) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B574584E04
3.375,0.406 3.792,0.656 0.417,0.25 4.802,0.406 5.219,0.656 0.417,0.25 1.969,0.417 2.385,0.667 0.417,0.25 4.896,0.438 5.208,0.635 0.313,0.198 10 false H46 3.458,0.438 3.771,0.635 0.313,0.198 10 false O47 2.052,0.448 2.365,0.646 0.313,0.198 10 false H45

a.

Disconnect the H45 and H46 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition Related Data List Item/DTC
H45-21 (STP1) - Body ground Stop light switch signal Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less
Power Source Control

Stop Light Switch


H46-6 (+B) - H46-29 (E) Power source Ignition switch off 11 to 14 V -
H46-14 (P) - H46-29 (E) P position signal Shift lever in P → Shift lever not in P 30 kΩ or higher → Below 200 Ω
Power Source Control

Shift P Signal


H45-22 (CUTB) - Body ground Dark current cut pin* Ignition switch off 11 to 14 V -
H46-29 (E) - Body ground GND Always Below 1 Ω -
H46-23 (SSW3) - Body ground SSW3 contact signal Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 3


H46-27 (SSW2) - Body ground SSW2 contact signal Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 2


H46-19 (SSW1) - Body ground SSW1 contact signal Power switch pushed → Power switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 1


H45-13 (SPD) - Body ground Vehicle speed signal Always 30 kΩ or higher
Power Source Control

Vehicle Running Condition (Line)



*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Connect the H45 and H46 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition Related Data List Item/DTC
H45-21 (STP1) - H46-29 (E) Stop light switch signal Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less
Power Source Control

Stop Light Switch


H46-11 (SLP) - H46-29 (E) Steering lock position signal Steering locked → Steering unlocked 11 to 14 V → 1.5 V or less
Power Source Control

Steering Unlock Switch


H46-24 (SLR+) - H46-29 (E) Steering lock motor operation command signal
(Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift lever is in P.


Pulse generation
(See waveform 1)
-
H46-8 (LIN) - H46-29 (E) LIN communication line Ignition switch ON Pulse generation
Entry&Start

Steering Lock Start Condition


H45-1 (IGB) - H46-29 (E) IGB signal Ignition switch off → Ignition switch ON 1 V or less → 8.5 V or higher -
H46-14 (P) - H46-29 (E) P position signal Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less
Power Source Control

Shift P Signal


H46-23 (SSW3) - H46-29 (E) SSW3 contact signal Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 3


H46-27 (SSW2) - H46-29 (E) SSW2 contact signal Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 2


H46-19 (SSW1) - H46-29 (E) SSW1 contact signal Power switch not pushed → Power switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 1


H46-21 (ACCD) - H46-29 (E) ACC signal Ignition switch off → Ignition switch ACC 1 V or less → 8.5 V or higher
Power Source Control

ACC Relay Monitor


H45-11 (IGRD) - H46-29 (E) IG signal Ignition switch off → Ignition switch ON 1 V or less → 9 V or higher
Power Source Control

IGR Relay Circuit (Outside) Monitor


H45-24 (IGPD) - H46-29 (E) IG signal Ignition switch off → Ignition switch ON 1 V or less → 9 V or higher
Power Source Control

IGP Relay Circuit (Outside) Monitor


H45-13 (SPD) - H46-29 (E) Vehicle speed signal Vehicle being driven at approx. 5 km/h (3 mph) Pulse generation
(See waveform 2)
Power Source Control

Vehicle Running Condition (Line)


H46-28 (SPDO) - H46-29 (E) Vehicle speed signal Vehicle being driven at approx. 5 km/h (3 mph) Pulse generation
(See waveform 2)
-
H45-2 (ST2) - H46-29 (E) STSW signal With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1 V or less -
H46-4 (CLG5) - H46-29 (E) Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
H46-5 (CG5B) - H46-29 (E) Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
O47-10 (CLG7) - H46-29 (E) Output to No. 2 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
O47-9 (CG7B) - H46-29 (E) Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
H46-30 (AGND) - Body ground Transponder key amplifier ground Always Below 1 Ω -
H46-12 (ANT1) - H46-30 (AGND) Signal input / output from transponder key coil (transponder key coil built into power switch) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of power switch pressed


Pulse generation
(See waveform 4)
Entry&Start

Encrypt Code Difference


H46-13 (ANT2) - H46-30 (AGND) Signal input / output from transponder key coil (transponder key coil built into power switch) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of power switch pressed


Pulse generation
(See waveform 4)
H46-25 (IND) - H46-29 (E) Security indicator output Ignition switch off → ON Pulse generation → Below 2 V -
O47-20 (WCSW) - H46-29 (E)*1 Wireless charger system stop signal Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Ignition switch off → ACC


Below 1 V → 4.5 to 6 V (For 1 second after ignition switch to ACC) -

*1: w/ Wireless Charger System


HINT:
·

The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.

·

The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:

-

To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the ignition switch to ACC or ON.

-

To lock the steering, open a door with the ignition switch off and the shift lever in P.





e.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561C09
1.521,1.583 2.375,1.74 0.854,0.156 2.281,0.479 2.729,0.635 0.448,0.156 0.24,0.417 1.635,0.615 1.396,0.198 2.01,1.75 2.198,2.042 2.198,2.042 2.323,2.042 false 0.948,0.406 2.927,0.25 2.927,0.25 2.521,0.479 false 2.927,1.594 3.313,1.792 0.385,0.198 10 GND 2.969,0.146 3.208,0.385 0.24,0.24 10 *a 2.375,1.979 2.552,2.146 0.177,0.167 10 *b
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1

Measurement Condition
Item Content
Tester Connection H46-24 (SLR+) - H46-29 (E)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift lever is in P.




ii.
B220145N21
2.875,1.177 3.229,1.344 0.354,0.167 10 false GND

Waveform 2

Measurement Condition
Item Content
Tester Connection H45-13 (SPD) - H46-29 (E)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle being driven at approx. 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



iii.
B574602C02
0.385,0.99 0.844,1.188 0.458,0.198 10 false GND 1.292,1.906 1.75,2.104 0.458,0.198 10 false *a 2.5,1.906 2.958,2.104 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Waveform 3

Measurement Condition
Item Content
Tester Connection H46-4 (CLG5) - H46-29 (E)
H46-5 (CG5B) - H46-29 (E)
O47-10 (CLG7) - H46-29 (E)
O47-9 (CG7B) - H46-29 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




iv.
B574585N01
0.427,1 0.885,1.198 0.458,0.198 10 false GND

Waveform 4

Measurement Condition
Item Content
Tester Connection H46-12 (ANT1) - H46-30 (AGND)
H46-13 (ANT2) - H46-30 (AGND)
Tool Setting 20 V/DIV., 200 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of power switch pressed






CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


C396298E05
1.75,0.792 2.146,1.063 0.396,0.271 1.823,0.833 2.281,1.031 0.458,0.198 10 false H71

a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H71-1 (GND) - Body ground Ground Always Below 1 Ω -
H71-7 (B) - Body ground Constant power supply Ignition switch off 11 to 14 V -


c.

Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Measure the voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H71-3 (IGE) - H71-1 (GND) Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Ignition switch turned off


Pulse generation
(See waveform 1)
Entry&Start
·

Power Supply Short History

·

Unlock Request Receive

·

Steering Lock Request Receive


H71-4 (SLP1) - H71-1 (GND) Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V
Entry&Start

Sensor Malfunction History


H71-5 (LIN) - H71-1 (GND) LIN communication line Ignition switch ON Pulse generation
Entry&Start

Steering Lock Start Condition


H71-6 (SLA) - H71-1 (GND) Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Ignition switch off → ON Below 1 V → 11 to 14 V -

HINT:
·

There is 1 motor and 2 sensors built into the steering lock actuator or upper bracket assembly.

·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P, and then open a door.





e.
C221561C69
1.542,1.583 2.396,1.74 0.854,0.156 2.271,0.479 2.719,0.635 0.448,0.156 0.24,0.427 1.635,0.625 1.396,0.198 0.896,0.427 2.75,0.25 2.75,0.25 2.938,0.25 false 2.75,0.25 2.5,0.469 false 1.969,1.74 2.094,2.042 2.094,2.042 2.177,2.042 false 2.927,1.604 3.313,1.802 0.385,0.198 10 false GND 2.99,0.198 3.24,0.417 0.25,0.219 10 false *a 2.229,1.969 2.479,2.135 0.25,0.167 10 false *b
*a Steering lock motor not operating
*b Steering lock motor operating


Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1

Measurement Condition
Item Content
Tester Connection H71-3 (IGE) - H71-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P

·

Steering unlocked

·

Ignition switch turned off





CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B510664E04
3.302,0.125 3.677,0.406 0.375,0.281 3.385,0.198 3.844,0.396 0.458,0.198 10 false H67

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition Related Data List Item
H67-1 (+B) - Body ground Power source Ignition switch off 11 to 14 V -
H67-5 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H67 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition Related Data List Item
H67-3 (EFII) - H67-5 (GND) EFI communication input
(Signal input from hybrid vehicle control ECU to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V Entry&Start
·

EFI Code Receive

·

Start Request


H67-3 (EFII) - H67-5 (GND) EFI communication input
(Signal input from hybrid vehicle control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
H67-4 (EFIO) - H67-5 (GND) EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU)
Ignition switch off Below 1 V
H67-4 (EFIO) - H67-5 (GND) EFI communication output
(Signal output from ID code box (immobiliser code ECU) to hybrid vehicle control ECU)
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)
H67-2 (LIN1) - H67-5 (GND) LIN communication line Ignition switch ON Pulse generation Entry&Start
·

Steering Lock Start Cond




e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Item Content
Tester Connection H67-3 (EFII) - H67-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Item Content
Tester Connection H67-4 (EFIO) - H67-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery




CHECK HYBRID VEHICLE CONTROL ECU


A458547N01
4.49,0.198 4.969,0.531 0.479,0.333 2.313,0.198 2.792,0.531 0.479,0.333 4.625,0.292 5.083,0.49 0.458,0.198 10 false H44 2.448,0.292 2.906,0.49 0.458,0.198 10 false A68

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H44-26 (IGP) - H44-15 (E1) Ignition power supply Ignition switch ON 11 to 14 V -
A68-33 (IGR) - H44-15 (E1) Ignition power supply Ignition switch ON 11 to 14 V -
H44-15 (E1) - Body ground Ground Always Below 1 Ω -
H44-39 (IMO) - H44-15 (E1) EFI communication output
(Signal output from hybrid vehicle control ECU to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V
·

EFI Code Receive

·

Start Request


H44-39 (IMO) - H44-15 (E1) EFI communication output
(Signal output from hybrid vehicle control ECU to ID code box (immobiliser code ECU))
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
H44-25 (IMI) - H44-15 (E1) EFI communication input
(Signal input from ID code box (immobiliser code ECU) to hybrid vehicle control ECU)
Ignition switch off 11 to 14 V → 1 V or less
H44-25 (IMI) - H44-15 (E1) EFI communication input
(Signal input from ID code box (immobiliser code ECU) to hybrid vehicle control ECU)
Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection H44-39 (IMO) - H44-15 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection H44-25 (IMI) - H44-15 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery




CHECK POWER SWITCH


B516200E02
3.313,0.208 3.708,0.521 0.396,0.313 3.396,0.292 3.854,0.49 0.458,0.198 10 false H69

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H69-3 (GND) - Body ground Transponder key amplifier ground Always Below 1 Ω -
H69-11 (SS3) - H69-3 (GND) SS3 contact signal
HINT:

Backup for SS1. Behaves the same way as SS1.


Power switch not pushed → Power switch pushed 9 V or higher → Below 1 V Power Source Control
·

Start Switch 3


H69-6 (SS2) - H69-3 (GND) SS2 contact signal
HINT:

Backup for SS1. Behaves the same way as SS1.


Power switch not pushed → Power switch pushed 9 V or higher → Below 1 V Power Source Control
·

Start Switch 2


H69-12 (SS1) - H69-3 (GND) SS1 contact signal Power switch not pushed → Power switch pushed 9 V or higher → Below 1 V Power Source Control
·

Start Switch 1




b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H69-1 (ANT1) - H69-3 (GND) Signal input / output from transponder key coil (transponder key coil built into power switch) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of power switch pressed


Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



H69-7 (ANT2) - H69-3 (GND) Signal input / output from transponder key coil (transponder key coil built into power switch) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of power switch pressed


Pulse generation
(See waveform 2)


c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B574585N01
0.427,1 0.885,1.198 0.458,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection H69-1 (ANT1) - H69-3 (GND)
H69-7 (ANT2) - H69-3 (GND)
Tool Setting 20 V/DIV., 200 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of power switch pressed