WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS (for Hatchback) > WHEEL ALIGNMENT STANDARD



MEASURE VEHICLE HEIGHT
C235025E01

Vehicle Height (Unloaded Vehicle) 
Tire Size
Front A-B
Rear C-D
P175/65 R15
97 mm
(3.82 in.)
32 mm
(1.26 in.)
P195/50 R16
101 mm
(3.98 in.)
32 mm
(1.26 in.)
175/65 R14
69 mm
(2.72 in.)
4.0 mm
(0.16 in.)
185/60 R15
69 mm
(2.72 in.)
4.0 mm
(0.16 in.)

Measuring points:
A:
Ground clearance of front wheel center
B:
Ground clearance of front lower arm set front bolt center
C:
Ground clearance of rear wheel center
D:
Ground clearance of axle beam set bolt center

NOTICE:
  1. Before inspecting the wheel alignment, check the vehicle height.
  2. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

HINT:
Bounce the vehicle up and down at the corners to stabilize the suspension before inspecting the vehicle height.


INSPECT WHEEL TURNING ANGLE


    C132439E12
  1. Fully turn the steering wheel left and right, and measure the wheel turning angle.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

    Wheel Turning Angle (Unloaded Vehicle) 
    Tire Size
    Inside Wheel
    Outside Wheel
    P175/65 R15
    40°44 ' +/- 2°
    (40.73° +/- 2°)
    35°03'
    (35.05°)
    P195/50 R16
    32°26' +/- 2°
    (32.43° +/- 2°)
    29°26'
    (35.43°)
    175/65 R14
    41°33' +/- 2°
    (41.55° +/- 2°)
    35°40'
    (35.67°)
    185/60 R15
    41°33' +/- 2°
    (41.55° +/- 2°)
    35°40'
    (35.67°)
    If the right and left inside wheel angles are not within the specified range, check the right and left rack end lengths.


INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
C132440E17
  1. Put the front wheel on the center of the alignment tester.
    Text in Illustration 
    *1
    Alignment tester
    *2
    Camber-caster-steering axis inclination gauge

  2. Remove the wheel cap.

  3. Set the camber-caster-steering axis inclination gauge at the center of the axle hub or drive shaft.

  4. Inspect the camber, caster and steering axis inclination.

    Camber Inclination (Unloaded Vehicle) 
    Tire Size
    Camber
    P175/65 R15
    -0°21' +/- 45'
    (-0.35° +/- 0.75°)
    P195/50 R16
    -0°24' +/- 45'
    (-0.40° +/- 0.75°)
    175/65 R14
    0°00' +/- 45'
    (0.00° +/- 0.75°)
    185/60 R15
    0°00' +/- 45'
    (0.00° +/- 0.75°)

    Caster Inclination (Unloaded Vehicle) 
    Tire Size
    Transmission
    Caster
    P175/65 R15
    C50
    U340E
    4°59' +/- 45'
    (4.98° +/- 0.75°)
    P195/50 R16
    C50
    U340E
    5°00' +/- 45'
    (5.00° +/- 0.75°)
    175/65 R14
    C50
    4°31' +/- 45'
    (4.52° +/- 0.75°)
    U340E
    4°30' +/- 45'
    (4.50° +/- 0.75°)
    185/60 R15
    C50
    4°32' +/- 45'
    (4.53° +/- 0.75°)
    U340E
    4°31' +/- 45'
    (4.52° +/- 0.75°)

    Steering Axis Inclination (Unloaded Vehicle) 
    Tire Size
    Steering Axis Inclination
    (Reference)
    P175/65 R15
    11°21'
    (11.35°)
    P195/50 R16
    11°26'
    (11.43°)
    175/65 R14
    10°43'
    (10.72°)
    185/60 R15
    10°43'
    (10.72°)

    NOTICE:
    1. Perform the inspection while the vehicle is empty (without a spare tire or tools on board).
    2. The tolerance for the difference between the left and right wheels is 30' (0.5°) or less for both the camber and caster.

  5. Remove the camber-caster-steering axis inclination gauge and attachment.

  6. Install the wheel cap.
    If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and wear.


INSPECT TOE-IN
  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  2. Release the parking brake and move the shift lever to the neutral position.

  3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



  4. C241642E01
  5. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (Dimension B).
    Text in Illustration 
    *a
    Tread Center Mark

  6. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



  7. C241643E01
  8. Measure the distance between the tread center marks on the front side of the wheels (Dimension A).
    Text in Illustration 
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle) 
    Tire Size
    Specified Condition
    P175/65 R15
    B-A: 1.2 +/- 2.0 mm
    (0.0472 +/- 0.0787 in.)
    P195/50 R16
    B-A: 0.9 +/- 2.0 mm
    (0.0354 +/- 0.0787 in.)
    175/65 R14
    B-A: 1.2 +/- 2.0 mm
    (0.0472 +/- 0.0787 in.)
    185/60 R15
    B-A: 1.3 +/- 2.0 mm
    (0.0512 +/- 0.0787 in.)
    If the toe-in is not within the specified value, adjust it at the rack ends.