FIT STANDARD / ADJUSTMENT METHOD (for Hatchback) > ADJUSTMENT



INSPECT HOOD SUB-ASSEMBLY


  1. Check that the clearance measurements are within the standard ranges.


    B284557E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.0 to 6.0 mm
    (0.0787 to 0.236 in.)
    D
    2.3 to 5.3 mm
    (0.0905 to 0.208 in.)
    B
    11.0 mm
    (0.433 in.)
    E
    1.2 to 5.2 mm
    (0.0472 to 0.204 in.)
    C
    5.0 mm
    (0.196 in.)
    -
    -

HINT:
Centering bolts are used to mount the hood hinge and the hood lock. The hood and the hood lock cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST HOOD SUB-ASSEMBLY


    B271586
  1. Loosen the 4 hood side hinge bolts.

  2. Move the hood to adjust the clearance to within the standard range.

  3. Tighten the 4 hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  4. B284563
  5. Adjust the height of the hood front end by turning the 2 center hood cushions.

    HINT:
    The center hood cushion can be raised and lowered by turning it.



  6. Adjust the hood lock.



      B273453
    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


INSPECT FRONT DOOR


  1. Check that the clearance measurements are within the standard ranges.


    B284596E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    3.0 to 6.0 mm
    (0.118 to 0.232 in.)
    F
    3.0 mm
    (0.118 in.)
    B
    2.1 to 5.1 mm
    (0.0826 to 0.200 in.)
    G
    3.6 to 6.6 mm
    (0.141 to 0.259 in.)
    C
    3.5 to 6.5 mm
    (0.137 to 0.255 in.)
    H
    -1.5 to 1.5 mm
    (-0.0590 to 0.0590 in.)
    D
    2.9 mm
    (0.114 in.)
    I
    5.5 to 8.5 mm
    (0.216 to 0.334 in.)
    E
    3.5 to 6.5 mm
    (0.137 to 0.255 in.)
    J
    5.5 to 8.5 mm
    (0.216 to 0.334 in.)

HINT:
Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST FRONT DOOR

NOTICE:
Make sure that the ignition switch is always OFF during adjusting door lock strikers.



    B284597
  1. Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

    SST
    09812-00010  

  2. Tighten the body side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  3. B284598
  4. Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.

    SST
    09812-00010  

  5. Tighten the door side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  6. B271647
  7. Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

  8. Using a "TORX" socket wrench T40, tighten the striker mounting screws after the adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


INSPECT REAR DOOR


  1. Check that the clearance measurements are within the standard ranges.


    B284604E01


    Standard:

    Area
    Specified Condition
    Area
    Specified Condition
    A
    3.6 to 6.6 mm
    (0.141 to 0.259 in.)
    D
    1.2 to 4.2 mm
    (0.0472 to 0.165 in.)
    B
    -1.5 to 1.5 mm
    (-0.0590 to 0.0590 in.)
    E
    2.8 to 5.8 mm
    (0.110 to 0.228 in.)
    C
    3.5 to 6.5 mm
    (0.137 to 0.255 in.)
    F
    5.5 to 8.5 mm
    (0.216 to 0.334 in.)

HINT:
Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST REAR DOOR

NOTICE:
Make sure that the ignition switch is always LOCK during adjusting door lock strikers.



    B271648
  1. Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

    SST
    09812-00010  

  2. Tighten the body side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  3. B284605
  4. Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.

    SST
    09812-00010  

  5. Tighten the door side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  6. B271650
  7. Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


INSPECT BACK DOOR


  1. Check that the clearance measurements are within the standard ranges.


    B271644E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    6.0 to 9.0 mm
    (0.236 to 0.354 in.)
    I
    3.0 to 8.0 mm
    (0.118 to 0.314 in.)
    B
    -0.5 to 2.5 mm
    (0.0196 to 0.0984 in.)
    J
    4.0 to 6.0 mm
    (0.157 to 0.236 in.)
    C
    6.0 to 9.0 mm
    (0.236 to 0.354 in.)
    K
    -1.5 to 1.5 mm
    (-0.0590 to 0.0590 in.)
    D
    -0.2 to 2.8 mm
    (0.00787 to 0.110 in.)
    L
    3.2 to 7.2 mm
    0.125 to 0.283 in.)
    E
    4.1 to 7.1 mm
    (0.161 to 0.279 in.)
    M
    3.2 to 7.2 mm
    (0.125 to 0.283 in.)
    F
    1.3 to 4.3 mm
    (0.0511 to 0.169 in.)
    N
    3.4 to 7.4 mm
    (0.133 to 0.291 in.)
    G
    4.5 to 7.5 mm
    (0.177 to 0.295 in.)
    O
    3.8 to 7.8 mm
    (0.149 to 0.307 in.)
    H
    -1.0 to 2.0 mm
    (-0.0393 to 0.0787 in.)
    -
    -

HINT:
Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts in. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST BACK DOOR


    B271651
  1. Adjust the door position.

    1. Horizontally and vertically adjust the door by loosening the door side hinge bolts.

      Torque:
      19 N*m{ 194 kgf*cm , 14 ft.*lbf }



  2. B271652
  3. Adjust the striker position.

    1. Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a plastic hammer.

    2. Using a "TORX" socket wrench T40, tighten the striker mounting bolts after the adjustment.

      Torque:
      23 N*m{ 235 kgf*cm , 17 ft.*lbf }