FIT STANDARD / ADJUSTMENT METHOD (for Sedan) > ADJUSTMENT



INSPECT HOOD


  1. Check that the clearance measurements are within the standard ranges.


    B140679E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.35 to 6.35 mm
    (0.092 to 0.250 in.)
    C
    2.0 to 5.0 mm
    (0.079 to 0.197 in.)
    B
    -2 to 2 mm
    (-0.079 to 0.079 in.)
    -
    -

HINT:
Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts on. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST HOOD


    B136202
  1. Loosen the hood side hinge bolts.

  2. Move the hood to adjust the clearance to within the standard range.

  3. Tighten the hood side hinge bolts after the adjustment.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  4. B136203
  5. Adjust the height of the hood front end by turning the cushion rubber.

    HINT:
    The cushion rubber can be raised and lowered by turning it.



  6. B136204
  7. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock position so that the striker can enter it smoothly.

    3. Tighten the 3 bolts after the adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


INSPECT FRONT DOOR


  1. Check that the clearance measurements are within the standard ranges.


    B140680E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.5 to 5.5 mm
    (0.098 to 0.217 in.)
    E
    3.3 to 6.3 mm
    (0.130 to 0.248 in.)
    B
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    F
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    C
    3.2 to 6.2 mm
    (0.126 to 0.244 in.)
    G
    4.2 to 7.2 mm
    (0.165 to 0.283 in.)
    D
    1.3 to 4.3 mm
    (0.051 to 0.169 in.)
    -
    -

HINT:
  1. Before adjusting the door position on vehicles equipped with side airbags and curtain shield airbags, be sure to disconnect the battery. After the adjustment, inspect the SRS warning light, the side airbag system and the curtain shield airbag system for normal operation. Then initialize both airbag systems.
  2. Use the same procedure for the RH and LH sides.
  3. The procedures described below are for the LH side.
  4. Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST FRONT DOOR
  1. Disconnect the cable from the negative battery terminal.
    Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



  2. B140683
  3. Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

    SST
    09812-00010  

  4. Tighten the body side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  5. B140684
  6. Adjust the door horizontally and vertically by loosening the door side hinge bolts.

  7. Tighten the door side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  8. B106966
  9. Using "Torx" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

  10. Using "Torx" socket wrench T40, tighten the striker mounting screws after the adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  11. Connect the cable to the negative battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


INSPECT REAR DOOR


  1. Check that the clearance measurements are within the standard ranges.


    B140681E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    3.3 to 6.3 mm
    (0.130 to 0.248 in.)
    E
    2.5 to 5.5 mm
    (0.098 to 0.217 in.)
    B
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    F
    2.5 to 5.5 mm
    (0.098 to 0.217 in.)
    C
    3.2 to 6.2 mm
    (0.126 to 0.244 in.)
    G
    -1.5 to 1.5 mm
    (-0.059 to 0.059 in.)
    D
    1.3 to 4.3 mm
    (0.051 to 0.169 in.)
    H
    4.2 to 7.2 mm
    (0.165 to 0.283 in.)

HINT:
  1. Before adjusting the door position on vehicles equipped with side airbags and curtain shield airbags, be sure to disconnect the battery. After the adjustment, inspect the SRS warning light, the side airbag system and the curtain shield airbag system for normal operation. Then initialize both airbag systems.
  2. Use the same procedure for the RH and LH sides.
  3. The procedures described below are for the LH side.
  4. Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST REAR DOOR
  1. Disconnect the cable from the negative battery terminal.
    Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



  2. B140685
  3. Adjust the door horizontally and vertically by loosening the body side hinge bolts.

  4. Tighten the body side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  5. B140686
  6. Adjust the door horizontally and vertically by loosening the door side hinge bolts.

  7. Tighten the door side hinge bolts after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  8. B106967
  9. Using "Torx" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

  10. Using "Torx" socket wrench T40, tighten the striker mounting screws after the adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  11. Connect the cable to the negative battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


INSPECT LUGGAGE COMPARTMENT DOOR


  1. Check that the clearance measurements are within the standard ranges.


    B140682E01


    Standard:

    Area
    Measurement
    Area
    Measurement
    A
    2.6 to 5.6 mm
    (0.102 to 0.220 in.)
    C
    6.45 mm
    (0.254 in.)
    B
    -0.6 to 1.4 mm
    (-0.023 to 0.055 in.)
    -
    -

HINT:
Centering bolts are used to mount the door hinge onto the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute standard bolts (with washers) for the centering bolts when making adjustments.


ADJUST LUGGAGE COMPARTMENT DOOR


    B140687
  1. Adjust the door position.

    1. Horizontally and vertically adjust the door by loosening the door side hinge bolts.

      Torque:
      7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



  2. B140688
  3. Adjust the striker position.

    1. Adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a plastic hammer.

    2. Tighten the striker mounting bolts after the adjustment.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }